valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. 3. Hold the tool firmly. 4. When driving into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL! Hold the tool only by the insulated grasping surfaces to prevent electric shock if you drive into a "live" wire. SAVE THESE INSTRUCTIONS. Charging Connect the charging plug to the charging connector, then plug in the charger to the power receptacle. Charging takes 3 hours. CAUTION: 0The battery in your new tool is not fully charged. You will need to charge it before use. 0 Do not operate the tool during charging. 0 Overcharging more than 2 days considerably shortens the battery service life. Always unplug the charger after completing the charge. When you charge a new tool or a tool which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the tool fully after discharging it almost completely a couple of times. Installing bit To install the bit, insert it into the tool as far as it will go. Switch action I To start the tool, move the slide switch Slide switch forward. Release it to stop. Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the revers- ing switch lever to the right for clockwise rotation or to the left for counterclock- wise. Reversing switch lever Counter- clockwise CAUTION: 0 Always check the direction of rotation before operation. 0Use the reversing switch only when the tool comes to a complete stop. Changing the direction of rotation before the tool stops may ruin the tool. Operation Place the point of the driver bit securely in the screw head and apply pressure to the tool to the extent that the bit will not slip off the screw. Then start the tool and drive the screw. CAUTION: 0 Use the proper bit for the head of the screw that you wish to use. 0 If the screw binds, turn the tool off immediately and perform manual driving operation. If you keep the switch on, the operating time per battery charge may be shortened. Also, it may cause a malfunction of the tool. Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. 0 When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the 3.1 (118") chart. 3.5 (9/64") Manual driving operation This tool can be used as a manual screwdriver when the switch is in the off position. Be sure to keep your finger off the switch when performing manual driving operation CAUTION: When performing manual driving operation, do not insert a screwdriver, etc. into the hole in the end of the tool to increase torque on the screw. This may cause tool damage. Application Dimensions of screw Workpiece Fastenings Wood screws 3.1 mm x 20 mm (1/8”x 3/4”) Lauan wood 220 screws (5/32“ x 3/4”) 110 screws ~~~~~ ~ Machine screws 1 5 mm (13/64”) I I 400 screws MAINTENANCE CAUTION : Always be sure that the tool is switched off before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this . -....~. manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Bits 0 Quick charger (A.C. only) Model DC2000 I Size I Part NO. Ph11 lips 784214-0A #++F 1 Slotted 784010-OA Sep--16-'87 EN CORDLESS SCREWDRIVER Model 6720D Note: The switch and other part configurations may differ from country to country. MODEL 6720D Sep-16 '87 EN ITEM NO. NO. USE0 DESCRIPTION $fD DESCRIPTION 1 1 Steel Ball 2 4 14 1 Motor 2 1 Leaf Spring 15 1 Change Knob 3 1 Plane Bearing 10 16 1 SwWh Lever 4 1 Retaining Ring S 10 17 1 Housinq Set [With Item 241 5 1 Flat Washer 10 18 1 Stopper Guide 6 1 Thrust Ball Bearing 1018 19 I stopper 7 1 Flat Washer 10 20 1 Compresslo" spmg 4 8 1 Spindle 21 1 Switch 9 3 Spur Gear 25 22 1 Circuit Board 10 1 Spur Gear 9 23 1 Bette," 11 3 Spur Gear 25 24 1 Housing Set [With Item 171 I2 1 Infernal Gear 60 25 I Name Plate 13 , 1 Flat Waaher 8 26 5 Tapping Screw 3x16 Note The Switch and other part specification4 may differ from country 10 country P Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. Ni-Cd To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 6720D (565.07 kb)