valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge Charging light are on the same sides as their respective markings on the fast charger. Insert the Start button Reset button cartridge fully into the port so that it rests on the charger port floor. Press the start button (red). The charging light will come on and charging will begin. If the charging light does not come on, press the reset button (yellow) first, then the start button (red). If the charging light goes out within 10 seconds even after pressing the reset button and start button a couple of times, the battery cartridge is dead. (CAUTION: Wait for more than 5 seconds after the charging light goes out to press the reset button again.) Replace it with a new one. When the charging light goes out in a certain time, you may remove the fully charged battery cartridge. Refer to the table below for the charging time. Fast charger DC9700 DC1201 DC9015 DC9112 Battery cartridge 9100, 9100A Approx. 60 min. Approx. 45 min. Approx. 15 min. Approx. 60 min. 9101, 9101A Approx. 60 min. -- ~~ When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. If you try to charge a cartridge from a just-operated tool, sometimes the charging light will not come on. If this occurs, let the cartridge cool off for a while. Then re-insert it and try to charge it once more. Do not keep the button pressed in with tape, etc. or the circuit will not function properly. Also, a malfunction of the charger may result possibly causing overheating, etc. If you wish to charge two battery cartridges, allow 15 minutes between chargings on the fast charger. Installing or removing the bit CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit. Use only the driver bit or socket bit shown 11 mm at right. Do not use any other driver bit or socket bit. 4 9 mm (3/8") To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release Bit I 7 the sleeve to secure the bit. I Sleeve To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly. NOTE: If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not be secured. In this case, try re-inserting the bit according to the instructions above. Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTIO N : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change Reversing switch the direction of rotation. Slide the reversing switch up for clockwise rotation or slide it down for counterclockwise rotation. Clockwise rotation 1 Counterclockwise Switch trigger CAUTION: Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20 -30 seconds before resuming operation. Adjusting the fastening torque The fastening torque can be adjusted infi- Red mark -Adjusting ring nitely from approx. 5 kg .cm (0.4ft . Ibs) to 37 kg . cm (2.7 ft . Ibs). To adjust it, loosen the two screws and turn the adjusting ring. Then tighten the screws to secure the adjusting ring. Refer to the table below fok relation between the numbers on the adjusting ring and the fastening torque to be obtained. Screw Number Numbers on adjusting ring Fastening torque to be obtained 1 5 kg . cm (0.4 ft . Ibs) I 2 I 10 kQ . cm (0.7 ft . Ibs) I 3 18 kg .cm (1.3 ft . Ibs) 4 27 kg . cm (2.0 ft . lbsl 5 37 kg . cm (2.7 ft . Ibs) (Example) 10 kg . cm (0.7 ft .Ibs) of fastening torque can be obtained when the number 2 is aligned to the red mark. NOTE: Always tighten the two screws to secure the adjusting ring after adjusting the fastening torque. Operation The proper fastening torque may differ depending upon the kind or size of screws, the type of materials to be fastened, the condition of the threads, etc. Before starting your job, always perform a test operation to verify adequate fastening torque. Hold the tool firmly and place the point of the driver bit in the screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw and turn the tool on. As soon as the screw becomes tight, the clutch will cut in and the motor will st...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 6703D (729.22 kb)