valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Handelsgesellschaft mbH Burgstra.e 21 · D-44867 Bochum (Germany) . BENCH DRILL PTBM 350-13 For drilling in wood, plastic and metal Please read carefully through the following information concerning safety and proper use. Before reading, fold out the page with the illustrations and make yourself familiar with all the functions of the equipment. Please read the operating instructions below and the accompanying safety advice carefully. Use the equipment only as described and for the indicated purposes. By doing this you will be able to work in complete safety and produce better results. Be careful to keep these advice notes and if necessary pass them on to a third party. PROPER USE The bench drill is intended for drilling in wood, plastic and metal using normal drill bits up to a maximum diameter (o) of 13 mm. Any other use of or modification to the machine shall be considered as improper use and could give rise to serious danger. SPECIFIC SAFETY ADVICE . In addition, you must also read the advice in the accompanying booklet called "Safety advice" before using the equipment for the first time. When you are using the bench drill always wear ear protectors and protective glasses. We recommend that you wear robust anti–slip footwear, a working apron or close-fitting clothing, If you have long hair you should wear some sort of hair protection (such as a hair net, cap or headscarf) to ensure that your hair does not become trapped in moving machine parts or twisted about the drill bit or chuck. Do not wear gloves when drilling. Do not remove any mechanical or electrical safety devices. Always check that all safety devices are attached and properly fixed in place. Always check that the workpiece is firmly and securely clamped in place. Never drill a workpiece whilst holding it in your hands. Check that the chuck is properly attached. . Never clean or lubricate the bench drill when it is in motion. Before adjusting, maintaining or repairing the drill, always remove the plug from the mains socket. Use a hand brush to remove drilling swarf. Ensure that you work safely by firmly fixing down the machine on to a working surface. Always keep the drive/ belt cover closed to keep hands and fingers out. Always use the key to open or close the drill chuck. FEATURES OF THE PTBM 350-13 Base plate 3 column/base fixing screws Drilling table 4 drill vice screws Drill vice Column Motor unit On/off switch 4 Chuck Drill chuck guard Drive/belt cover Drive/belt cover handle * Adjustment screw Handle/spindle control Table clamp screw Contacts * Drive (motor side) } Gears Drive (spindle side) Depth stop with scale Adjustment nut * = form and type may differ from that shown in the illustrations TECHNICAL INFORMATION Mains connection: 230 V ~ 50 Hz Spindle speed: 1. Setting: 2600 rpm Current: 1.9 A 2. Setting: 1750 rpm Nominal power: 350 W 3. Setting: 1250 rpm Nom. speed, no load: n0 1400 rpm (motor) 4. Setting: 900 rpm Power factor: 0.8 5. Setting: 600 rpm Duty cycle: 60 % Drilling capacity: 13 mm Spindle travel: 50 mm Sound pressure level: 75 dB (A) Vibration: 2.5 m/s2 (vibration) Weight: approx. 19.5 kg We reserve the right to make technical modifications and changes without notice to the appearance of the equipment in the course of further development. ASSEMBLY The bench drill is supplied ready to assemble. Remove the parts carefully from the packaging and assemble the bench drill in the following manner: 1. Insert the column into the base plate and tighten the screws (3 column/base fixing screws ). 2. Place the drilling table on to the column and fix it in position using the table clamp screw . 3. Fix the drill vice (4 drill vice screws ) on to the drilling table . 4. Place the pre-assembled motor unit on to the column. The motor unit is attached by two hexagonal socket screws on the right hand side. 5. Attach the three armed handle/spindle control in the rise and fall shaft. 6. Attach the chuck firmly to the drill spindle cone. Attention: Clean the drill spindle cone thoroughly to remove all traces of grease. SETTING UP THE MACHINE Set the bench drill down on a firm surface and level it using a spirit level. We recommend that the machine is bolted down on to the supporting surface. Please ensure that the base plate is not subject to any additional forces as a result of being bolted down. 5 INSTALLATION AND FIRST USE Check that the supply type, voltage and fuses comply with those specified for the machine. First clean any anti-rust coating carefully from the parts. Then oil the column. SWITCHING THE MACHINE ON AND OFF Insert the plug into the mains socket and switch on the machine using the "I” button at the on/off switch . To switch off use the “0” button. CHECKING AND TENSIONING THE V-BELT Open the drive/belt cover and check the V-belt tension. If it is correctly adjusted the V-belt should be able to be moved approximately 1 cm in the middle between the two drive wheel...