valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
9. Use only one charger when charging. 10. Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black & Decker service center. 11. DO NOT incinerate the tool or batteries even if they are severely damaged or completely worn out. The batteries can explode in a fire. 12. A small leakage of liquid from the battery cells may occur under extreme usage, charging or temperature conditions. This does not indicate a failure. However, if the outer seal is broken and this leakage gets on your skin: a. Wash quickly with soap and water. b. Neutralize with a mild acid such as lemon juice or vinegar. c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 2535% solution of potassium hydroxide. Charging Procedure IMPORTANT: The batteries in your tool are not fully charged at the factory. Before attempting to charge them, thoroughly read all of the safety instructions. To charge the tool, follow the steps below: 1. Plug the output cord of the charger into the socket in the bottom half of the tool cradle as shown in Figure 1. 2. Plug the charger into any standard 120 Volt 60 Hz electrical outlet. 3. Place the ISD600 Impact Driver into the cradle making sure to match the charging contacts on the handle of the impact driver with the contacts in the charger. The red (charging) light will illuminate indicating that the charging process has started. The light will stay on as long as the battery is in the charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a different color when 1 the charging cycle is complete. 4 90503227 ISD600 Impact Driver 6/15/06 12:52 PM Page 5 4. Let the tool charge initially for 9 hours. WARNING: When disconnecting the tool from the charger, be sure to unplug the charger from the outlet first, then disconnect the charger cord from the tool cradle. Important Charging Notes 1. After normal usage, your tool should be fully charged in 3 to 9 hours. If the batteries are run down completely, it may take up to 9 hours to become fully charged. Your toolwas sent from the factory in an uncharged condition. Before attempting to use it, itmust be charged for at least 9 hours. 2. DO NOT charge the batteries in an air temperature below 40°F (4,5 °C) or above105°F (+40,5 °C). This is important and will prevent serious damage to the batteries. Longest life and best performance can be obtained if batteries are charged when airtemperature is about 75°F. 3. While charging, the charger may hum and become warm to touch. This is a normalcondition and does not indicate a problem. 4. If the batteries do not charge properly: (1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power offwhen you turn out the lights. (3) Move charger and tool to a surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). (4) If the receptacle and temperature are okay, and you do not get proper charging, refer to your warranty. 5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in adepleted condition. 6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although overcharging is not a safety concern, it can significantlyreduce overall battery life. 7. The batteries will reach optimum performance after being recharged 5 times during normal usage. There is no need to run the batteries down completely beforerecharging. Hanging the Charging Base (fig. 2 & 3) Use the hardware provided only if hanging on conventional hollow wall construction such as sheet rock or plaster walls. If not hanging on conventional sheet rock or plaster walls, please use the appropriate fasteners for that material. The charger can be fixed to the charger mounting bracket as described below, or simply placed, in a convenient level position. • Locate the charger mounting bracket within reach of an electrical outlet. • Mark the position of both hang holes as shown in figure 2. • The mounting screws should be driven in to about an 1/8” (3mm) from the wall. • Place the charger mounting bracket over the screw heads and slide down until fully seated. • Finish tightening the screws and check to see that the bracket is firmly attached to the wall so it will not pull out. • Place the charger in position until it “clicks” into place as shown in figure 3. Safety Warnings and Instructions: Drilling 2 3 • Hold tool firmly to control its twisting action. WARNING: Tool may stall (if overloaded or improperly used) causing a twist. To reduce the risk of injury always expect the stall. Grip the tool firmly to control the twisting action and prevent loss of control which could cause personal injury. ...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 90503227 (384.57 kb)