Log:
valutazioni - 0, GPA: 5 ( )

Istruzioni per l'uso Black & Decker, Modello Scrudrivers 4063SD

Produttore : Black & Decker
File Size : 149.25 kb
File Nome :
Lingua di insegnamento: enesfr
Vai a scaricare



Facilità d'uso


NOTE: Align ribs on inside of depth locator with grooves in clutch housing. English 3 GRB/386312-02 8/11/00 1:56 PM Page 4 English DEPTH ADJUSTMENT 1. For washer head screws: rotate adjustment nutsetter is flush with end of locator. 2. For large washer head and sealer screws: adjust nutsetter is recessed approximately 1/16" into 3. Test drive a fastener in scrap material to determine correct. 4. Adjust following the graphic printed on the tool. Accessories Recommended accessories for use with your tool are available at extra cost from your distributor or local service center. CAUTION: The use of any non-recommended accessory may be Maintenance CLEANING With the motor running, blow dirt and dust out of all air vents with dry air at least once a week. Wear safety glasses when performing this operation. Exterior plastic parts may be cleaned with a damp cloth and mild detergent. Although these parts are highly solvent resistant, NEVER use solvents. CHANGING CLUTCHES 1. Remove clutch housing by unscrewing (left hand thread). 2. Clamp tool or clutch housing in a resilient clamp.USE CARE, the clutch housing can be easily damaged. 3. Remove round clutch retaining rings with a very small screwdriver (see Figure 2). 4. Install new clutches and new retaining rings. The spring should FIG. 2 run against the output clutch spindle. NOTE: If the output spindle slides toward inside of gear case, remove gear case and push output spindle forward to expose retaining ring groove. Reassemble dead spindle spring allowing no more than 1/4" projecting from end of spindle. 5. Relubricate clutches (see Parts Bulletin for DEWALT lubricants identification). LUBRICATION All ball and needle bearings are factory lubricated for the life of the bearing. CLUTCH LUBRICATION 1. Remove clutch housing by unscrewing (left hand thread). 2. Lightly brush clutch faces.hazardous. Important To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. 4 GRB/386312-02 8/11/00 1:56 PM Page 5 Full Warranty GRABBER heavy duty industrial tools are warranted from date of purchase. We will repair, without charge, any defects due to faulty materials or workmanship. For information, call 1-800-477-TURN. This warranty accessories or damage caused where repairs have attempted by others. This warranty gives you specific you may have other rights which vary in certain states 5 English GRB/386312-02 8/11/00 1:56 PM Page 6 Francais POUR TOUT RENSEIGNEMENT SUPPLEMENTAIRE SUR CET OUTIL OU TOUT AUTRE OUTIL GRABBER, COMPOSER FRAIS LE NUMERO: 1 800 477-TURN (1 800 433-8876) REGLES DE SECURITE GENERALES AVERTISSEMENT! Vous devez lire et comprendre toutes les instructions. Le non-respect, meme partiel, des instructions ci-apres entraine un risque de choc electrique, d’incendie et/ou de blessures graves. CONSERVEZ CES INSTRUCTIONS. AIRE DE T...

Questo manuale è adatto anche per i modelli :
Trapani e shuropopverty - Scrudriver 4025 (149.25 kb)
Trapani e shuropopverty - Scrudrivers 386312-02 (149.25 kb)
Trapani e shuropopverty - Scrudrivers 4060 (149.25 kb)
Trapani e shuropopverty - Scrudrivers 4063 (149.25 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie