valutazioni - 5, GPA: 3.6 ( )

Produttore : Black & Decker File Size : 1.11 mb File Nome : Lingua di insegnamento:

Damage to the chuck and personal injury may occur when changing accessories. OPERATING THE LASER Your drill is equipped with a laser which is turned on and off separately from the tool. WARNING: NEVER aim the beam at a workpiece with a reflective surface. Bright shiny reflective sheet steel or similar reflective surfaces are not recommended for laser use. Reflective surfaces could direct the beam back toward the operator. CAUTION: LASER RADIATION. AVOID DIRECT EYE EXPOSURE. Do not stare into the laser light source. Never aim light at another person or object other than the workpiece. Laser light can damage your eyes. WARNING: DO NOT use tinted glasses to enhance the laser light. Tinted glasses will reduce overall vision for the application and interfere with the normal operation of the tool. SWITCHING THE LASER ON AND OFF (FIGURE J) • To turn the laser on, slide the laser on/off button (6) to the (I) position. • To turn the laser off, slide the laser on/off button (6) to the (0) position. SETTING THE DIRECTION OF THE BEAM (FIGURE K) The laser beam can be set for both horizontal and vertical leveling applications. • To change the laser line projection, move the laser direction actuator (7) in the direction that you want the laser line to project. NOTE: Laser will not work if the drill is inverted. 10 90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 11 USING THE LASER LEVEL FUNCTION (HORIZONTALLY LEFT - FIGURE L) • Place the tool flat against the wall as shown. • Slide the laser on/off switch (6) to position I to switch the laser ON. • Move the laser direction actuator (7 in Figure K) to the left most position. Laser will project horizontally to the left from the laser aperture (5 in Figure B). • Move the tool as necessary to position the laser line. NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical. • Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted. USING THE LASER LEVEL FUNCTION (VERTICALLY - FIGURE M) • Place the tool flat against the wall as shown. • Slide the laser on/off switch (6) to position I to switch the laser ON. • Move the laser direction actuator (7 in Figure K) to the center position. Laser will project vertically from the laser aperture (5 in Figure B). • Move the tool as necessary to position the laser line. NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical. • Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted. USING THE LASER LEVEL FUNCTION (HORIZONTALLY RIGHT - FIGURE N) • Place the tool flat against the wall as shown. • Slide the laser on/off switch (6) to position I to switch the laser ON. • Move the laser direction actuator (7 in Figure K) to the right most position. Laser will project horizontally to the right from the laser aperture (5 in Figure B). • Move the tool as necessary to position the laser line. NOTE: The laser lines will only be level if the tool is kept within 5 degrees from vertical. • Slide the laser on/off switch (6) to position 0 to switch the laser OFF. NOTE: Laser will not work if the drill is inverted. SCREW DRIVING For driving fasteners, the reversing button should be pushed to the left. Use reverse (button pushed to the right) for removing fasteners. When moving from forward to reverse, or vice versa, always release the trigger switch first. ON BOARD BIT STORAGE A bit storage slot is built-in to the area just above the battery pack. DRILLING • Use sharp drill bits only. • Support and secure work properly, as instructed in the Safety Instructions. • Use appropriate and required safety equipment, as instructed in the Safety Instructions. • Secure and maintain work area, as instructed in the Safety Instructions. • Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from slipping out of it. • Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much as to stall the motor or deflect the bit. • Hold the drill firmly with two hands to control its twisting action. • DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT. • Minimize stalling on breakthrough by reducing pressure and slowly drilling through the last part of the hole. • Keep the motor running while pulling the bit out of a drilled hole. This will help reduce jamming. • Make sure switch turns drill on and off. 11 90504494 02 BDGL1200 drill 8/29/06 8:39 AM Page 12 MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service personn...

Scarica la tua

Per scaricare, digitare 2 cifre :