Log:
valutazioni - 2, GPA: 4 ( )

Istruzioni per l'uso Porter-Cable, Modello 902387

Produttore : Porter-Cable
File Size : 228.73 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Also, check for blown fuses or open circuit breakers in the line. CHECK CLUTCH CONDITION CAUTION: DISCONNECT TOOL FROM POWER SOURCE Periodically, depending on use, screwdriver clutch jaws should be inspected for wear. This may be done by removing the screwdriver mechanism housing (A), Fig. 5, from the power unit. NOTES: The clutch housing is attached to the power unit with left- hand threads. The depth stop assembly may be removed from the clutch housing to expose a set of wrenching “flats” (B), Fig. 5, on the clutch housing. These “flats” permit the use of a wrench to aid in clutch housing removal. B B A Fig. 5 9 902387 - 10-31-01.qxd 2/12/02 3:30 PM Page 10 There is a small spring in the end of the power unit spindle shaft. Be careful not to lose this spring. Note condition of 3-jaw clutch faces on power unit and screwdriver mechanism. If they are badly rounded where the angular face meets the top surface, or appear otherwise worn or faulty, or if the clutch elements are not securely held in place on their respective shafts by the snap rings, return the entire tool to your AUTHORIZED PORTER-CABLE SERVICE STATION for service. If the jaws are not seriously worn and there are no other apparent faults in the mechanism, then proceed and be sure that the mechanism and all internal areas are clean and free of chips or other foreign material and brush a thin coat of PORTER-CABLE gear lubricant on the clutch elements and surrounding areas. Reassemble the screwdriver mechanism onto the power unit. Be sure the spring is on the spindle shaft. NOTE: The housing threads are left-hand thread. BRUSH INSPECTION AND LUBRICATION For your continued safety and electrical protection, brush inspection and replacement on this tool should ONLY be performed by an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA SERVICE CENTER. At approximately 100 hours of use, take or send your tool to your nearest Authorized Porter-Cable Service Station to be thoroughly cleaned and inspected; worn parts replaced, when necessary; relubricated with fresh lubricant, if required; reassembled with new brushes; and performance tested. Any loss of power before the above maintenance check may indicate the need for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is present, return your tool to the Service Station for immediate service. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations, including brush inspection and replacement, should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or a PORTER-CABLE/DELTA SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give all information shown on the nameplate of your tool (model number, type, serial number, etc.). 10 902387 - 10-31-01.qxd 2/12/02 3:30 PM Page 11 ACCESSORIES A complete line of accessories is available from your Porter-Cable • Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Porter- Cable Authorized Service Stations. Please visit our Web Site for a catalog or for the name of your nearest supplier. WARNING: Since accessories other than those offered by Porter-Cable • Delta, have not been tested with this product use of such accessories could be hazardous. For safest operation, only Porter-Cable • Delta recommended accessories should be used with this product. IMPORTANT NOTE: Size of screwdriver accessories should be chosen so as not to exceed the specified capacity of driver with which they are to be used. 11 902387 - 10-31-01.qxd 2/12/02 3:30 PM Page 12 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material during the warranty period. For repair or replacement return the complete tool or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof of purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service Centers or Authorized Service Stations. ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE OF PURCHASE. To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, Jackson, Tennessee 38305...

Questo manuale è adatto anche per i modelli :
Trapani e shuropopverty - 6640 (228.73 kb)
Trapani e shuropopverty - 6642 (228.73 kb)
Trapani e shuropopverty - 6641 (228.73 kb)
Trapani e shuropopverty - 6645 (228.73 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie