valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using product with its batteries in a depleted condition. 6. To prolong battery life, avoid leaving on charge for extended periods of time (over 30 days without use). Although extended charging is not a safety concern, it can significantly reduce overall battery life. Safety Warnings and Instructions: WARNING: Tool may stall (if overloaded used) causing a twist. To reduce the risk of injury always Grip the tool firmly to control twisting action and prevent loss If a stall does occur, release the trigger immediately re-starting. ASSEMBLY AND ADJUSTMENT WALL MOUNTING THE CHARGING CRADLE (A, B) The charging cradle can be placed on a level hardware provided only if hanging on conventional hanging on conventional sheet rock or plaster walls, fasteners for that material. • Choose a location that is within reach of an electrical outlet. • If wall mounting, space mounting screws the same distance as the slots on the back of the charger shown in figure A. NOTE: Avoid damaging the cord while fixing the charging cradle (10) to the wall. • Plug in charger and place the product in position ( figure B). Make sure the charge indicator light (9) is on. If the indicator light is not on, adjust unit to make sure charging contacts (8) are touching. INSERTING AND REMOVING BITS (FIGURE C) • To install a bit simply insert it into the cavity in the hex spindle (6) as shown in figure C. To remove the bit pull it straight out. TORQUE CONTROL ( FIGURE D) Your screwdriver is equipped with a six position clutch collar (4). When the tool reaches preselected torque setting the clutch slips, thus limiting how tightly a screw is driven. • The tool. s motor will continue to run as long as the switch button is depressed. • To set the tool. s torque, rotate the adjustable clutch collar (4) clockwise or counterclockwise as required (figure D) . The larger the screw icon, the higher the torque. Each click in a clockwise direction (facing the spindle ) means an increase in the torque produced. FORWARD / REVERSE / LOCK OFF SLIDER (FIGURE E) • To select forward or reverse rotation, use the forward / reverse slider (2) (see arrows on the slider). A window (3) on the top of the unit will display the rotating direction with an arrow ( figure E). NOTE: When the forward / reverse slider is in the central position the tool is locked off to prevent accidental actuation or battery discharge. OPERATING INSTRUCTIONS SWITCHING ON AND OFF • To run the tool, press the switch (1). • To stop the tool, release the switch. • To lock the tool in the off position, move the forward / reverse slider (2) to the central position. SCREW DRIVING • Insert the appropriate screwdriver bit into the hex spindle. • Select forward or reverse rotation. • Set the clutch collar to the smallest screw icon and begin driving screw (low torque). • If the clutch ratchets too soon, adjust the clutch collar to increase the torque as required. SCREW DRIVING USING THE BUILT-IN SCREW HOLDER (FIGURES F - I) The screw holder (7) can be used with both one and two inch screwdriver bits. It cannot be used with bit tip holder extensions. To use the screw holder: • Grasp the screw holder carrier and pull it out from the screwdriver. ( figure F) • Place desired screw onto screw holder carrier ( figure G). Ensure screw threads rest on screw carrier as shown. 8 9 90564630 5/25/10 7:45 AM Page 10 • Slide screw holder arm screw head are fully engaged. figure H) • At this time the screw is being internal magnet. Note: Magnet will not work on non-ferrous • Ensure unit is set for driving screws • While driving the screw, the screw holder carrier and arm head to be driven to its desired depth figure I). • After use, return screw holder arm back from damage. Screw driving Notes: • Do not use double ended screwdriver bits. • Do not use screwdriver as a pry bar in any position. • To avoid screwdriver being turned on accidentally, do not carry in your pocket. LED LIGHT A light (5) is built-in to the screwdriver above the spindle (6). To use the light without the spindle turning, place the forward / reverse selector (2) in the DRILLING • Insert the appropriate hex shank drill bit. • Select the largest screw icon on the clutch collar for maximum torque. • Select forward rotation. NOTE: When drilling, the bit may become disconnected from the spindle upon withdrawing it from the material. Should this occur, the bit can be removed by re-inserting the hex shank into the spindle and running the tool in the reverse direction. GENERAL DRILLING TIPS • This tool is not recommended for drilling in masonry. • Use sharp drill bits only. • Drill bits for metal can be used for drilling holes in wood. These bits must be sharp and should be pulled out frequently when drilling to clear chips from the flutes. • Support and secure work properly, as instructed in the safety Instructions. • Use appropr...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - Li4000 (1.07 mb)