valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Minimum Gage for Cord Sets Volts Total Length of Cord in Feet 120V 0-25 26-50 51-100 101-150 240V 0-50 51-100 101-200 201-300 Ampere Rating More Not more American Wire Gage Than Than 0-618 16 16 14 6 -10 18 16 14 12 10-12 16 16 14 12 12 -16 14 12 Not Recommended ASSEMBLY/ADJUSTMENT SET-UP WARNING: Always unplug drill from power supply before any of the following operations. SIDE HANDLE (1/2" DRILLS ONLY) • If your drill is equipped with a side handle, it must be installed properly in order to control the drill. • Insert bolt into recessed hole with molded hex shape, making sure that hex head is seated fully to prevent bolt from turning. • Place circular opening over drill chuck and onto front of drill gear case. • Place the drill on its side and holding the bolt head with your finger, thread handle onto bolt. The handle now has a full range of 360 degrees around the drill. OPERATING INSTRUCTIONS WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool. SWITCH To turn the drill ON squeeze the trigger switch. The farther the trigger is depressed, the higher the speed of the drill. To turn the tool OFF release the trigger switch. The drill can be locked ON (maximum RPM only) for continuous use by squeezing the trigger while pushing in on the locking button (Fig .1). Hold the locking button in while you release the trigger switch and then release the locking button. The drill will continue to run. To turn the drill OFF from a locked ON condition, squeeze and release the trigger. WARNING: The drill should only be locked ON when it is held stationary in a drill press stand or other means; NOT BY HAND! Never unplug the tool with the locking feature engaged. To do so will cause the tool to start immediately the next time it is plugged in. FORWARD/REVERSE (DR200, DR210, DR220, DR300, DR400, DR402, DR600) To select forward rotation push the switch control lever to the RIGHT (when viewed from the chuck end) (Fig.1). To select reverse push the lever to the LEFT (when viewed from the chuck end). After all reversing operations, switch the tool to the forward running mode. NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE. DO NOT FORCE TRIGGER. SELECT FORWARD OR REVERSE BEFORE TURNING DRILL ON. FORWARD/REVERSE (DR500 ONLY) To select forward rotation push the switch control lever to the LEFT (when viewed from the chuck end) (Fig.1). To select reverse push the lever to the RIGHT (when viewed from the chuck end). After all reversing operations, switch the tool to the forward running mode. NOTE: WHEN THE SWITCH CONTROL LEVER IS IN THE CENTER POSITION THE DRILL WILL NOT OPERATE. DO NOT FORCE TRIGGER. SELECT FORWARD OR REVERSE BEFORE TURNING DRILL ON. CHUCK & KEY OPERATION (DR200, DR400, DR500, DR600) Turn chuck collar to open chuck jaws. Place bit in chuck as far as it will go. Tighten chuck collar by hand. Place chuck key in each of the three holes, and tighten in clockwise direction (Fig. 2). Tighten chuck with all three holes to prevent slippage. KEYLESS CHUCK OPERATION (DR210, DR220, DR300, DR402) DR220 -Single Sleeve Chuck with Automatic Spindle Lock -This tool is equipped with a feature that automatically locks the spindle when the tool is not running. This anti-rotational feature is a normal condition which allows for tightening or loosening of the chuck with one hand operation. Loosen the chuck by rotating the sleeve counterclockwise (Fig. 3). Insert the bit or other accessory fully into the chuck, and tighten securely by rotating the sleeve in the clockwise direction as viewed from the chuck end. DR210, DR300, DR402 - To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to rotate the front half in the counterclockwise direction. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as viewed from the chuck end. HAMMER ACTION (DR400, DR402, DR600) Your drill has hammer action which is engaged by sliding the hammer/drill selector lever. To select hammering, turn off the drill and rotate the lever shown in Figure 4 so that the arrow on the lever points to to the hammer symbol on the drill housing. To select drilling, turn off the drill and rotate the lever so that the arrow on the lever points to the drill symbol. WARNING: Do not attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and turning the tool on. Damage to the chuck and personal injury may occur when changing accessories. DRILLING • Always unplug the drill when attaching or removing accessories. When attaching accessories in the drill chuck, it is important to securely tighten the chuck using all three holes to prevent slippage. When using a keyless chuck, hand tighten firmly. . • Use sharp drill bits only. • Support and secure work...