valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Lisez le mode d’emploi avant d’utiliser cet outil. Vor Benutzung des Werkzuegs bitte bedienungsanleitungen sorgfaltig lesen. Antes de utilizar esta herramienta, lean las instrucciones. Lees instructies alvorens dit hulpmiddel in werking te stellen. BUILD® Operating Instructions Important Please read these operating and safety instructions carefully and completely. For your own safety, before using this equipment check that the voltage is correct and that all handles and parts are firmly secured. If you are uncertain about any aspect of using this equipment contact your distributor. Please Keep These Instructions Model BORA 2800 Specifications Motor (230v or 115v 50/60 Hz) (Watts): 1200 Maximum Cutter Diameter: 1-1/8” (USA) 28mm (UK/EU) Maximum Cutting Depth: 2” 50mm RPM No Load (min-1): 570 Recommended Maximum Duty Cycle (Minutes): 30 Sound Pressure Level (Under Load) (dB(A)): 90 Weight: 31lb 14kg Max Dimensions (Rack Fully Raised): 23-1/4”x8-1/2”x12-1/8” 585x220x310 Min Dimensions (Rack Fully Lowered): 17-3/4”x5-1/8”x12-1/8” 450x130x310 Magnet Dimensions: 2”x3-1/8”x6-1/2” 50x80x164 Magnetic Adhesion: 2860lb 1300kg Cutter Retainer Internal Diameter: 3/4” 19mm Weldon Shank Standard Equipment Supplied With Unit: 1 Coolant Tank, 1 Coolant Pipe, 1 Guard, 3 Hex keys, 3 Handles, 2 Butterfly Screws, 2 Spring Washers, 1 Chain, 1 Chuck, 1 Chuck Key, Carry Case. Ear and eye protection MUST be worn while operating this equipment. Do NOT touch the cutter while it is in motion. Always follow the Personal Protection Equipment (PPE) recommendations while operating this tool. This machine is designed specifically for drilling holes in mild steel using the appropriate cutters and accessories. It should NOT be modified and / or used for any application other than for which it was intended, including powering other equipment. Ensure that the total work area can be viewed from the operating position. Use barriers to keep people away. Do not operate the tool in explosive environments – power tools create sparks that may ignite flammable materials or gases. Do not operate the tool in damp or wet conditions or areas, as electric shocks may result. Always use both hands to operate the tool. Always ensure that the material you are working on is securely clamped. • This tool is equipped with an approved cord and plug for its intended Country of use. The green and yellow conductor in the cord is the grounding wire, never connect this to a live terminal. • Remove plug from power supply before replacement of the cutter, making adjustments or other maintenance work. • We recommend the use of genuine Evolution supplied cutters. • Inspect the machine and cutter before each use and do not use deformed, cracked, worn or otherwise damaged cutters. • Ensure the cutter is correctly mounted and do not stop by hand. • Do not use cutters that do not comply with the characteristics specified in these instructions. • Ensure that the gibs (dovetail slides) are correctly adjusted before each use. This is essential for proper and safe operation of the machine. • Always keep the power cord away from moving parts of the tool. • When you put the tool away, switch off the motor and ensure that all moving parts have come to a complete standstill. • Never use the tool without the original protection guard system. Machine Set Up: Changing Cutters To insert a cutter, first insert the pilot pin. Then slide the cutter into the adaptor, align the proper flat with the locking screw(s) and tighten securely with the supplied hex wrench. CAUTION: Ensure that the locking screw is on a flat of the cutter and not just against the rounded shank. To remove cutter, reverse the procedure. Ensure that the coolant feed tap is on and coolant feeds properly by pushing the pilot pin. If it feeds too quickly or slowly, adjust the tap accordingly. Keep the tap closed when not in use. 2 EC – Declaration of Conformity We, Evolution Power Tools Limited Venture One Longacre Close Sheffield S20 3FR as the supplier of the product listed below: BORA 2800 Magnetic Drill Part Number: BORA28001/BORA28002/BORA28002EU Voltage: 110/230v Power: 1200W Declare, under our sole responsibility that the equipment to which this document relates, is in conformity with the following standards or other normative documents:EN60335- 1: 1994+A1+A2+A11-A16 EN55014-1: 2000+A1+A2 EN55014-2: 1997+A1 EN61000-3-2: 2000 EN61000-3-3: 1995+A1 EN61000-3-11: 2000 and thereby conforms to the protection requirements of Council Directive 73/23/EEC amended by 93/68/EEC relating to the Low Voltage Directive, Council Directive 98/37/EEC relating to the Machine Directive and Council Directive 89/336/EEC relating to the EMC Directive, and is compliant with Council Directive 2002/95/EC in relation to the Restriction of Hazardous Substances in electrical & electronic equipment (RoHS). EU Directive 2002/95/EC restricts the use of the 6 substances below in the manufacture of specific types of electrical equipment. Whilst this re...