valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
!WARNING Safety glasses and ear protection must be worn during operation. 3. Do not wear loose fitting clothing, scarves, or neck ties in work area. Specifications Tool Voltage 120 V, 60 Hz Chuck Size 1/2" Max Bit Size 1/2" Blows per Minute 42,000 RPM 0 - 2800 Power Rating 6 Amps REMINDER: Keep your dated proof of © 2006 Campbell Hausfeld/Scott Fetzer For parts, product & service information IN713300AV 3/06 20 visit Operating Instructions and Parts Manual General Safety Information (Cont’d.) Loose clothing may become caught in moving parts and result in serious personal injury. 4. Do not wear jewelry when operating any tool. Jewelry may become caught in moving parts and result in serious personal injury. 5. Always use attachments designed for use with this tool. Do not use damaged or worn attachments. 6. Never trigger the tool when not applied to a work object. Attachments must be securely attached. Loose attachments can cause serious injury. 7. Never point a tool at oneself or any other person. Serious injury could occur. 8. Use steady, even pressure when using tool. Do not force. Too much pressure can cause blade to break or overheat. 9. Keep all nuts, bolts and screws tight and ensure equipment is in safe working condition. 10. Do not put hands near or under moving parts. WORK AREA !WARNING Do not operate a power tool in an explosive atmosphere, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the fumes or dust. !CAUTION Keep work area clean and well lighted. Cluttered benches and dark areas invite accidents. !CAUTION Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. ELECTRICAL SAFETY !WARNING Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. !WARNING Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. !WARNING Do not abuse cord. • Never carry tool by its cord. • Never pull the cord to disconnect from receptacle. Pull plug at the outlet. 1. Do not operate tool with damaged cord or plug. • Have a damaged or worn power cord and/or strain relief replaced immediately. • Do not attempt to repair power cord. 2. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 3. Do not use an extension cord unless absolutely necessary. Use of improper extension cord could result in a risk of fire and electric shock. If an extension cord must be used, make sure: • That the pins on plug of extension cord are the same number, size and shape as those of plug on tool cord. • That the extension cord is properly wired and in good electrical condition. • If an extension cord is to be used outdoors it must be marked with the suffix “W-A” or “W” following the cord type designation to indicate it is acceptable for outdoor use. For example – SJTW-A 4. Do not expose cord to rain, snow or frost. PERSONAL SAFETY !WARNING Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician. 1. Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. !CAUTION Avoid accidental starting. Be sure switch is in the locked or off position before plugging in the 2 tool. Carrying tools with your finger on the switch or plugging in a tool with the switch on invites accidents. 2. Remove adjusting keys or wrenches before turning on the tool. A key or wrench attached to a rotating part of the tool may result in personal injury. 3. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better control of the tool in unexpected situations. 4. Always work in a well-ventilated area. Wear an OSHA-approved dust mask and safety glasses. 5. Hold tool by insulated gripping surface when performing an operation where the tool may contact hidden wiring. Contacting a “live” wire will make exposed metal parts of the tool “live” and shock the operator. 6. Keep hands away from rotating parts. 7. Use clamps or another practical way to secure the workpiece to a stable platform. Never hold work in your hand, lap, or against other parts of your body when cutting. TOOL USE AND CARE !WARNING Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. 1. This tool must NOT be modified or used for any application other than that for which it was designed. !CAUTION Do not force...