valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
SERvICE a. by qualified repair personnel. b. When servicing a tool, use only identical replacement parts. Use only authorized parts. c. Use only the lubricants supplied with the tool or specified by the manufacturer. the tool without first obtaining written approval from Campbell Hausfeld. Do not use the tool if any shields or guards are removed or altered. Do not use the tool as a hammer. Personal injury or tool damage may occur. AIR SOURCE a. Never connect to an air source that is capable of exceeding 200 psi. Over pressurizing the tool is able to result in bursting, abnormal operation, breakage of the tool or serious injury to persons. Use only clean, dry, regulated compressed air at the rated pressure or within the rated pressure range as marked on within the rated air-pressure range. b. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons. Do not use any type of reactive gases, including, but not limited to, oxygen and combustible gases, as a power source. Use filtered, lubricated, regulated compressed air only. Use of a reactive gas instead of compressed air may cause the tool to explode which will cause death or serious personal injury. Do not misuse this product. Excessive Tool service must be performed only Do not make any modifications to the tool. Always verify prior to using the tool that the air source has been adjusted to the rated air pressure or Use only a pressure-regulated compressed air source to limit the air pressure supplied to the tool. The regulated pressure must not exceed 90 psi. If the regulator fails, the pressure delivered to the tool must not exceed 200 psi. The tool could explode which will cause death or serious personal injury. c. Do not exceed any pressure rating of any component in the system. SAvE THESE INSTRUCTIONS DO NOT DISCARD Operating Instructions LUBRICATION Proper lubrication is the owner’s responsibility. Failure to lubricate the air tool properly will dramatically shorten the life of the tool and will void the warranty. This impact wrench requires lubrication before the initial use and before and after each additional use. Impact wrenches require lubrication throughout the life of the tool and must be lubricated in two separate areas: the air motor and the impact mechanism. Air tool oil is recommended because this oil cleans, lubricates and inhibits rust all in one step. AIR MOTOR LUBRICATION The motor must be lubricated daily. An air motor cannot be oiled too often. Disconnect the impact wrench from the air supply before lubricating. 1. Disconnect the impact wrench from the air supply. 2. Turn the impact wrench upside down. 3. While pulling the trigger, squeeze approximately a 1/4 oz. of airtool oil in the air inlet. Then, push the forward and reverse button in both directions. OCO290 psi After an air tool has been lubricated, oil will discharge through the exhaust port during the first few seconds of operation. Thus, THE EXHAUST PORT MUST BE COVERED WITH A TOWEL before applying air pressure. FAILURE TO COVER THE EXHAUST PORT CAN RESULT IN SERIOUS INJURY. 4. Connect the impact wrench to the air supply and cover the exhaust port with a towel. Run the impact wrench in both the forward and reverse directions for 20 to 30 seconds. Oil will discharge from the exhaust port when air pressure is applied. IMPACT MECHANISM LUBRICATION Lubricate the impact mechanism monthly. Disconnect the impact wrench from the air supply before lubricating. 1. Disconnect the impact wrench from the air supply. 2. Remove the slotted screw or allen head screw from the oil port hole. 3. Squeeze approximately 1 oz. of air tool oil in the oil port hole. Replace the screw. 4. Reconnect the air supply to the impact wrench and run for 20 to 30 seconds. Lubricate the entire impact mechanism by rotating the tool upside down and sideways while running the tool. 5. Remove the screw and hold the oil port hole over a suitable container to allow excess oil to drain. Sometimes triggering the tool when dumping the oils helps to force out the excess oil. 6. If the oil is dirty, repeat the procedure above until the oil comes out clear. Install the screw and tighten. The residual oil remaining in the impact mechanism chamber is all that is needed for proper lubrication. 4 5 TL0517 Operating Instructions (Continued) Recommended Hookup The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the ...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - IN735300AV (3.57 mb)