valutazioni - 5, GPA: 4
(
)
)
|
Facilità d'uso
Lift the grip insert from the back of the handle. Install a new grip insert by first placing the tab (A) Fig. 7 at the top of the grip into the corresponding slot in the drill/driver handle. The retention fin (B) Fig. 7 will fit in the slot provided. Hold the grip against the handle, and insert and tighten the phillips head screw (B) Fig. 6 until snug. Do not over tighten. 9 OPERATION CHARGING THE BATTERY PACK GENERAL Before using your cordless tool for the first time, the battery pack should be fully charged. If the battery pack is installed in the tool, remove it by following instructions under INSTALLING OR REMOVING BATTERY PACK. As a battery pack approaches the discharged state, you will notice a sharp drop in tool performance. When the tool is unable to perform the task at hand, it is time to recharge the battery pack. Recharging the battery pack before this condition is reached will reduce the total work life of the pack. Discharging the pack beyond this point can damage the pack. NOTE: Battery temperature will increase during and shortly after use. Batteries may not accept a full charge if they are charged immediately after use. Allow the battery pack to cool to room temperature before charging for best results. The battery charger may rest on the four pads provided on the bottom of the case or be mounted on a wall by utilizing the two key hole slots provided. Vent slots in top and bottom of charger must not be obstructed. Do not charge battery when temperature is BELOW 40°F (4.44°C) or ABOVE 104°F (40°C). NORMAL CHARGING Make sure that the power circuit voltage is the same as that shown on the charger specification plate. Connect charger to power source. The green light (A) Fig. 8 should begin to flash. This indicates the charger is ready to begin charging. Position battery pack on charger, align rails on battery pack with four tabs (C) Fig. 8 on charger. Slide battery forward on charger until it stops. The green light (A) Fig. 8 should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge” (if the green light does not glow continuously, or if the red light (B) Fig. 8 also begins to flash, see "DIAGNOSTICS"). After approximately one hour, the “Fast Charge” indicator light should go out, indicating that the battery pack is fully charged and that the charger is now in a “Maintenance Charge” mode. The battery pack can be left on “Maintenance Charge” until you are ready to use it. Depending on room temperature, line voltage, and existing charge level, initial battery charging may take longer than one hour. A B C Fig. 8 Disconnect charger from power source when not in use. DIAGNOSTICS The Model 8604 charger is equipped with a diagnostic system that automatically checks the battery pack when it is inserted into the charger. If no problems are found, the charger will automatically switch to “Fast Charge” mode as described in "NORMAL CHARGING". 10 Problems will be indicated by charger indicator lights (see Fig. 8): • If the green light (A) continues to flash after battery pack is inserted in charger, the battery pack temperature is either too high or too low for charging. If left alone, the charger will continue to monitor the battery pack temperature and will begin charging when the temperature reaches an acceptable level. • If the green light (A) glows continuously and red light (B) flashes, the battery pack is receiving a “Fast Charge”, but the battery pack voltage is low. It is not unusual for a new, or a fully discharged battery pack to give this indication for the first several minutes of charge. If the red light continues to flash throughout the charge cycle, it indicates that the pack is weak and will provide reduced performance (the pack is still useable, but will not provide maximum power or work per charge). This battery pack will probably require replacement in the near future. • If the green light (A) continues to flash and red light (B) flashes, the battery pack has failed (pack is not chargeable and requires replacement). INSTALLING OR REMOVING BATTERY PACK To remove a battery pack, depress the battery release button (B) Fig. 9, and pull battery pack out of tool. To install a battery pack, align rails (A) Fig. 9 on battery pack with slots on tool and push battery pack onto tool until it locks in place. A B Fig. 9 HOW TO HOLD THE DRILL/DRIVER The front end of the Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 10A. IT’S A DRILL Fig. 10A 11 HOW TO HOLD THE HAMMER DRILL/DRIVER The front end of the Hammer Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 10B. IT’S A HAMMER DRILL GENERAL DRILLING 1. Set torque adjusting collar for drilling operation and set speed selector to appropriate speed. 2. Be sure drill bit is securely gripped in chuc...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 8723 (237.08 kb)
Trapani e shuropopverty - 966 (237.08 kb)