Log:
valutazioni - 2, GPA: 4 ( )

Istruzioni per l'uso Kawasaki, Modello 840062

Produttore : Kawasaki
File Size : 517.13 kb
File Nome : 2cd32333-e902-4383-9b88-633b35d2ace0.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Before first use, the battery pack requires 3-5 hours charge time to be fully charged. Subsequent recharging needs for the battery to be fully charged. Always switch to a fresh battery when tool performance begins to diminish. Severe heat is most destructive to a battery; the more heat generated, the faster the battery loses power. A battery that gets too hot can have a shortened life. Never over-discharge a battery by using the tool even after tool performance has decreased. Do not attempt to discharge a tool’s battery by continuing to pull on the tool trigger. When tool performance begins to diminish, stop the tool and recharge the battery for optimal performance. Charge battery pack at ambient temperatures between F – 104° F. Store tool and battery pack in locations where temperatures 120°F. This is important to prevent serious cells. The battery pack should always be recharged begins to run slowly. When battery pack is not in use, keep paper clips, coins, keys, make a connection Shorting the battery terminals together may cause 9 10 CHARGING BATTERY PACK REMOVING / ATTACHING BATTERY PACK REMOVING / ATTACHING BATTERY PACK REMOVE BATTERY PACK: 1. Press both release buttons on either side of the Cordless Impact Wrench to release the battery pack. 2. Pull battery pack free of Cordless Impact Wrench. ATTACH BATTERY PACK: 1. Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Impact Wrench. 2. Press the battery pack into place. Make sure the latches are securely fastened. Do not use the Cordless Impact Wrench if the battery pack is not seated properly. RELEASE BUTTON CHARGER Before using battery charger, please read carefully all instructions and cautionary markings on battery charger, battery pack and product using battery. Use only the charger which accompanied your product or direct listed in this manual. Do not substitute any other charger. Use only Alltrade approved chargers with your product. Do not disassemble charger. Do not use charger if it has been damaged, left outdoors wet or damp environments, or immersed in liquid. The battery pack and charger heat during charging. Place the charger on a flat, non-flammable surface away from flammable materials with clearance to allow proper air circulation around the charger and battery pack. When the battery pack requires recharging, a 1 hour operate at full power. A charging indicator light on the show that charging is taking 11 RELEASE BUTTON CHARGE (PRESS) BATTERY INDICATORHighMedLow BATTERY CHARGERLED LIGHT BATTERY PACK BATTERY PACK: 1. Plug the charger into the nearest 120 volt electrical outlet. 2. Make sure the trigger on the Cordless Impact Wrench is in the “OFF” position and remove the battery pack from the Cordless Impact Wrench. 3. Insert the battery pack into the charger. Be sure that the battery pack is fully seated in the charger. Do not force. 4. The red indicator light should come “ON” indicating that the battery pack is in a “Fast Charge” mode. If the green indicator light comes “ON” , then the battery is already fully charged. 5. After approximately one hour of charging, the red indicator light should go “OFF” and the green light should come “ON” indicating that the battery is fully charged and the charger is now in a “Trickle Charge” mode. 6. The battery can be left in a “Trickle Charge” mode until ready to use. IMPORTANT INFORMATION FOR RECHARGING HOT BATTERIES When using your Cordless Impact Wrench continuously, the batteries in your battery pack will become hot. You should let a hot battery pack cool down for approximately 30 minutes before attempting to recharge. When the battery pack becomes discharged and is hot, the red light on the charger will pack cools down, the red light will glow continuously mode, 1-hour charge time. This will occur when continuous use of Impact Wrench causes the battery pack to become hot. It does not occur under normal circumstances. 12 VARIABLE SPEED TRIGGER SWITCH ASSEMBLY ASSEMBLY Be aware that this tool is always in an operating condition because it does not have to be plugged into an electrical outlet. Always turn the switch “OFF” and remove the battery pack before changing bits. INSTALLING / REMOVING SOCKET ON THE ANVIL When removing the socket or bit from the tool, avoid contact with skin and use proper protective gloves when grasping the socket, bit or accessory. Accessories may be hot after prolonged use. When installing a socket, align the holes in the side of the socket with the dent pin. Press the socket on until the dent pin engages in the hole. To remove a socket, depress the dent pin through the hole using a small pointed object and pull the socket off. OPERATING THE IMPACT WRENCH Never tape the trigger switch down to provide continuous high speed. The tool may fail under such conditions causing fire personal injury. THIS TOOL IS CONTROLLED BY A TRIGGER SWITCH: • The speed of the Cordless Impact Wrench depends on the amount of pressure you pu...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie