valutazioni - 4, GPA: 4 ( )

Produttore : Hotpoint-Ariston File Size : 3.31 mb File Nome : Lingua di insegnamento:

It is advisable to install the oven so that it rests on two strips of wood, or on a completely flat surface with an opening of at least 45 x 560 mm (see diagrams). Positioning ! Keep packaging material out of the reach of children. It can become a choking or suffocation hazard. see Precautions and tips). ! The appliance must be installed by a qualified person in compliance with the instructions provided. Incorrect installation may cause harm to persons, animals or may damage property. Fitting the appliance Use the appropriate cabinet to ensure that the appliance functions properly. • The panels adjacent to the oven must be made of heat-resistant material. • Cabinets with a veneer exterior must be assembled with glues which can withstand temperatures of up to 100°C. • To install the oven under the counter (see diagram) and in a kitchen unit, the cabinet must have the following dimensions: Position the 4 tabs on the side of the oven according to the 4 holes of the outer frame. Adjust the tabs according to the thickness of the cabinet side panel, as shown below: thickness of 20 mm: take off the removable part of the tab (see diagram) thickness of 18 mm: use the first groove, which has already been set in the factory (see diagram) thickness of 16 mm: use the second groove (see diagram) ! The appliance must not come into contact with electrical parts once it has been installed. The consumption indications on the data plate have been calculated for this type of installation. Secure the appliance to the cabinet by opening the oven door and putting 4 screws into the 4 holes of the outer frame. ! All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool. 12 Electrical connections ! Ovens equipped with a three-pole power supply cable are designed to operate with alternating current at the voltage and frequency indicated on the data plate located on the appliance (see below). Fitting the power supply cable 1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram). 2. Loosen the cable clamp screw and remove it, using a screwdriver as a lever (see figure). 3. Remove the wire contact screws L-N- -±- , then fasten the wires under the screw heads, respecting the colour code: Blue (N), Brown (L) and Yellow-Green Verde Connecting the supply cable to the mains Install a standardised plug corresponding to the load indicated on the data plate (see side). The appliance must be directly connected to the mains using an omnipolar circuit-breaker with a minimum contact opening of 3 mm installed between the appliance and the mains, suitable for the load indicated and complying with current electrical regulations (the earthing wire must not be interrupted by the circuit-breaker). The supply cable must not come into contact with surfaces with temperatures higher than 50°C. ! The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations. Before connecting to the power supply, make sure that: • The appliance is earthed and the plug is compliant with the law. • The socket can withstand the maximum power of the appliance, which is indicated on the data plate (see below). • The voltage must be in the range between the values indicated on the data plate (see below). • The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets. ! Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible. ! The cable must not be bent or compressed. ! The cable must be checked regularly and replaced by authorised technicians only (see Assistance). ! The manufacturer declines any liability should these safety measures not be observed. DATA PLATE Dimensions width cm 43.5 height cm 32 depth cm 41.5 Volume lt. 58 Electrical connections voltage: 220-240V~ 50/60 Hz (see data plate) maximum power absorbed 2800W ENERGY LABEL Directive 2002/40/EC on the label of electric ovens. Norm EN 50304 Energy consumption for Natural convection - heating mode: [™[ Traditional mode l~J Declared energy consumption for Forced convection Class - heating mode: ^ Baking C€ A-*\ This appliance conforms to the following European Economic Community directives: -2006/95/EEC of 12/12/06 (Low Voltage) and subsequent amendments; - 2004/108/EEC of 15/12/04 (Electromagnetic Compatibility) and subsequent amendments; - 93/68/EEC of 22/07/93 and subsequent amendments. - 2002/96/EC and subsequent amendments. 13 Description of the appliance Overall view Control panel THERMOSTAT indicator light knob knob * knob THERMOSTAT indicator light knob TIMER knob knob * Only on certain models. 14 Start-up and use ! The first time you use your ap...

Scarica la tua

Per scaricare, digitare 2 cifre :