valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
This switches on the appliance, and it is now ready for use. The ~ symbol lights up. Switching on the appliance a= Risk of scalding! by hot water. The water in the water tank may become hot. Empty the water tank before starting operating modes that are not steam- assisted. Notes ¦ You can only start the / Low-temperature cooking operating mode when the oven has cooled down. There must be no residual heat ( • or oe) showing in the temperature display. ¦ For applications using steam assistance, you must fill the water tank ( see section: Filling and emptying the water tank) . 1. Switch on the appliance. 2. Turn the operating mode selector until the desired operating mode is selected. 3. Turn the temperature selector to change the default temperature. Note: If no default temperature is displayed, the temperature of your selected operating mode is a fixed setting. You cannot change this temperature. 4. Press the . Start button. Notes ¦ Depending on the operating mode selected, you will hear a pumping sound after starting. The appliance is checking whether the pumps are working correctly. ¦ If you cannot start a steam- assisted application, check whether the water tank has been filled and fully inserted. Operating mode Default temper- Temperature ature in °C range in ° C 3 CircoTherm ®* 160 40 - 220 % Top/ bottom heat* 170 50 - 275 0 Circotherm intensive* 220 50 - 275 4 Circo-roasting* 170 50 - 250 + Full-surface grill 220 50 - 275 + Full-surface grill ( inten- Fixed setting sive) * * ( Centre-area grill 180 50 - 275 ( Centre-area grill (inten- Fixed setting sive) * * $ Bottom heat 200 50 - 225 / Low-temperature cook- Fixed setting u u u ing A Defrost setting Fixed setting A A A z Oven cleaning Fixed setting ‹ a Reheat 120 80 - 180 * In this operating mode you can activate steam operation ** Turn the temperature selector to above 275 °C. ‚Y. appears in the temperature display Changing the operating mode 1. Turn the operating mode selector until the desired operating mode is selected. 2. Turn the temperature selector to change the temperature. 3. Press the . Start button. Current temperature Press the ± info button. The current temperature appears for 3seconds. Note: The current temperature can only be displayed with operating modes with a default temperature. Heating indicator The heating indicator displays the rising temperature in the cooking compartment. ¦ Temperature reached (figure A) ¦ Appliance reheating ( figure B) Filling and emptying the water tank a= Risk of injury and risk of fire! Only fill the water tank with water or with the descaling solution that is recommended by us. Do not pour any flammable liquids (e. g. alcoholic drinks) into the water tank. Due to hot surfaces, vapours from flammable liquids may catch fire in the cooking compartment (explosion). The appliance door may spring open. Hot steam and jets of flame may escape. Caution! The appliance may become damaged due to the use of unsuitable liquids. Do not use distilled water, highly chlorinated tap water (> 40 mg/l) or other liquids. Only use cold, fresh tap water, softened water or uncarbonated mineral water. Notes ¦ If you use mineral water, set the water hardness to hard. ¦ For hygiene reasons, a reminder message will appear after the appliance is switched off if the water tank has not been emptied. The reminder message goes out once the water tank is empty. Filling the water tank Fill the water tank before each use with steam assistance. 1. Press lightly on the centre of the lower edge of the water tank (picture A) . 2. Pull out the water tank (picture B) . 3. Fill the water tank with cold water up to the " max" mark (picture C) . 4. Slide in the water tank all the way. Note: If the I symbol flashes, the water tank has not been pushed in fully. Topping up the water tank If the water tank is empty, a signal sounds and the I symbol lights up. Steam- assisted operation is interrupted. 1. Pull out the water tank. 2. Fill the water tank up to the " max" mark and slide it in fully. The steam-assisted operation continues. Emptying the water tank Empty the water tank after each steam- assisted use of the appliance. 1. Turn the operating mode selector back to the U off position and push it in. The remaining water in the evaporator system is pumped back into the water tank. The I symbol lights up. .z © appears in the temperature display. (pumping-out). When the pumping out cycle is complete, a signal sounds and the I symbol flashes. 2. Pull out the water tank slowly and level. The I symbol goes out. 3. Remove the cover ( Picture A) . 4. Empty the water tank ( Picture B) . . . 5. Dry the tank shaft and water tank thoroughly. 6. Slide in the water tank. The I symbol and the .z © display ( pumping-out) go out. Switching off the appliance a= Risk of scalding! When opening the appliance door, hot steam may escape. After cooking, only open the appliance door carefully. Note: The appliance has a cooling fan. After the appliance is switched off, the...
Questo manuale è adatto anche per i modelli :Forni - B45C42N0GB/35 (1.82 mb)