valutazioni - , GPA:
(
)
)
Produttore : FUNAI
File Size : 8.31 mb
File Nome : 2275555d-d861-422c-b32f-d89ed604fe25.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
• Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the remote sensor of the unit. • Remote control for different devices can interfere with each other. Avoid using remote control for other equipment located close to the unit. • Replace the batteries when you notice a fall off in the operating range of the remote control. • The maximum operable ranges from the unit are as follows. - Line of sight: approx. 23 feet (7m) - Either side of the center: approx. 16 feet (5m) within 30° - Above: approx. 16 feet (5m) within 15° - Below: approx. 10 feet (3m) within 30° Installing batteries in the remote control Install two “AA” size batteries (supplied) matching the polarity indicated inside battery compartment of the remote control. Note: Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: • Do not mix new and old batteries together. • Do not use different kinds of batteries together, although they may look similar, different batteries may have different voltages. • Make sure that the plus and minus ends of each battery match the indications in the battery compartment. • Remove batteries from equipment that is not going to be used for a month or more. • When disposing of used batteries, please comply with governmental regulations or environmental public instruction’s rules that apply in your country or area. • Do not recharge, short-circuit, heat, burn or disassemble batteries. STANDBY-ON REW F.FWD STOP/EJECT PLAY VCR CHANNEL OPEN/CLOSE D.DUBBING STOP P V LAY CR DVD DVD RECORD S-VIDEO VIDEO AUDIO SOURCE RECORD L R SKIP REC PAUSE ETUP TOP MENU/ ORIGINAL k FWD g STOP C PLAY B REV h H G Remote control Within about 23 feet (7m) 30° 30° Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish to operate with [SOURCE]. STOP STANDBY-ON TIMER SET TIMER PREV NEXT OPEN/CLOSE SPACE 1 2 3 4 5 6 7 8 0 9 CH VIDEO/TV SLOW PAUSE .@/: ABC DEF GHI JKL MNO PQRS REC DISPLAY TUV WXYZ DVD REC REC MODE ZOOM SEARCH VCR SETUP CM SKIP TITLE DISC MENU RETURN DUBBING RAPID PLAY CLEAR OK PLAY AUDIO VCR DVD SOURCE DVD indicator VCR indicator SOURCE button VCR button DVD button STANDBY-ON REW F.FWD STOP/EJECT PLAY VCR CHANNEL OPEN/CLOSE D.DUBBING STOP PLAY VCR DVD DVD RECORD SOURCE S-VIDEO VIDEO AUDIO RECORD L R Press [VCR ] on the remote control. (Verify that the VCR indicator is lit.) Press [DVD ] on the remote control. (Verify that the DVD indicator is lit.) The VCR/DVD recorder switching Note: • Pressing only [SOURCE] on the front panel DOES NOT switch the mode of the remote control. You MUST select the correct mode on the remote control. • You cannot switch to another mode (DVD or VCR) during in the timer-standby mode. • Pressing [DVD REC] or [VCR REC] on the remote control switches immediately its respective mode so that you can start recording directly on the appropriate media. VCR MODE DVD MODE 1 2 3 E9A12UD_PY90VG_p01-40.indd 10 2006/04/27 17:23:32 11 Recording Playing discs Editing Before you start Connections Getting started SeCtuhpa mngeinnug the VCR functions Others Espanol EN Functional overview (cont’d) Before you start Setup menus Press [SETUP] to display the Setup menu, then press [OK] to display each menu, using [K / L]. These menus provide entries to all main functions of the unit. 1. Required Settings: To set up the required settings. 2. Playback: To set up the unit to play discs as you prefer. 3. Display: To set up the OSD screen and the front panel display of the unit as you prefer. 4. Recording: To set up the unit to record on discs or tapes as you prefer. 5. Clock: To set up the clock of the unit as you need. 6. Channel: To adjust the channel setting of the unit as you prefer. 7. Disc Edit / CD Playback Mode: “Disc Edit” is only available with disc recorded in this unit. (DVD+VR mode) “CD Playback Mode” is available only when an Audio CD disc, a CD-RW/R disc with MP3/WMA files or a Video CD is inserted into the unit. 1. Edit Disc Name: Allows you to rename the disc formatted with DVD+VR. 2. Disc Protect : Allows you to protect a disc from accidental editing or recording. 3. Erase Disc (DVD+RW/DVDRW only): Allows you to erase all contents in the disc and format it. 4. Make Edits Compatible (DVD+RW only): Allows you to make edits possible to play discs in other units after editing discs. Finalize (DVD+R/DVD-RW/ DVD-R only): Allows you to finalize a disc containing recorded titles. 5. Random Play: Allows you to activate the random playback feature. 6. Program Play (Audio CD/ Video CD only): Allows you to activate the programmed playback feature. 7. PBC (Video CD only): Allows you to select images or information on the menu screen by activation PBC (Playback control) function. Disc Edit Erase Disc Finalize Disc Protect OFF ON Edit Disc Name 23 112 34 3 Setup Playback Display Recording Clock Channel Disc Edit Required Settings 1234567 1234567 CD Playback Mode Program Play PB...