valutazioni - , GPA:
(
)
)
Produttore : Magma
File Size : 1.85 mb
File Nome : 7f9ac313-6e69-4ceb-be71-fc422866f8e2.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Hookups This section shows how the MDR24/96 is typically connected to both analog and digital consoles (using the Mackie Analog and Digital 8•Bus consoles as examples). These examples assume that the rest of your studio equipment (monitors, sound sources, outboard processing, etc.) is already connected, or that you know how to connect it. Before you begin, note how the three eight-channel I/O cards are arranged on the MDR24/96 rear panel: 1-8 is on the left, 9-16 is in the center, and 17-24 is on the right. Labeling each cable before you begin will make connecting the MDR24/96 to your console easier. The specific hookups for each MDR24/96 I/O card are shown below. Analog Hookup (AIO•8) This example describes the hookup for the 24•8 analog console. Cables & Hardware (3) AIO•8 cards for MDR24/96 (6) Analog snakes, DB25 to eight 1/4” TRS phone plugs Hookup 1. Connect three snakes to the MDR24/96 Inputs (bottom connector). If you want to have the ability to route any console input to any recorder track, then connect the 1/4” plugs on each of the three snakes to the like- numbered Submaster / Tape Output jacks on the 8•Bus console. This works as long as you don’t record more than 8-channels at a time, since the Submaster Outputs 9-16 and 17-24 are the same as outputs 1-8. Alternately, you can connect the console’s direct outputs to the recorder’s inputs, so that each console channel feeds the like-numbered recorder track. Or, you can use a combination of direct and subgroup outs. The hookup diagram below shows the MDR24/96 inputs connected to the Submaster Outputs. MDR24/96 back panel 24•8 SUBMASTER / TAPE OUTPUTS 8 7 15 6 14 5 13 4 12 3 11 2 10 1 9 TAPE RETURNS 1-8 15 13 11 9 7 5 3 1 16 14 12 10 6 4 28 17 18 19 20 21 22 23 24 16 TAPE RETURNS 9-16 TAPE RETURNS 17-24 171820 1921222324 INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT ANALOG I/O ANALOG I/O ANALOG I/O 120VAC 50/60 Hz 475W SYNC ACC ETHERNET MIDI 1-8 9-16 17-24 TAPE IN/OUTS INPUT OUTPUT INPUT OUTPUT INPUT OUTPUT ANALOG I/O ANALOG I/O ANALOG I/O 18 TAPE IN/OUTS MDR24/96 AIO Cards MDR 24/96 Note: Note:Note:Note:Note:Note: Some older AIO•8 cards have the Input jack la beled as “From Tape” and the Output jack labeled as “To Tape.” Otherwise, they operate identically. Sigh ... long story. 2. Connect three snakes to the MDR24/96 Outputs (top connector). Connect the plug end of the snakes to the like-numbered Tape Return jacks on the 24•8 console. MDR24/96 Settings 1. Set the Sample Clock to Internal. 2. Set the Sample Rate and Bit Depth according to your preference. Console Settings Set the 24•8 console to the nominal +4 dBu operating level by setting the five Operating Level switches in the Sub Out and Tape Return sections to the ‘out’ position. This example describes the hookup for the D8B console equipped for analog I/O. MDR 24/96 Digital 8•Bus AIO•8 Cards AIO•8 Cards INPUT OUTPUT ANALOG I/O INPUT OUTPUT ANALOG I/O INPUT OUTPUT ANALOG I/O (6) DB25 toDB25 AnalogSnakes INPUT OUTPUT ANALOG I/O INPUT OUTPUT ANALOG I/O INPUT OUTPUT ANALOG I/O TAPE IN/OUTS TAPE IN/OUTS Cables & Hardware (3) AIO•8 cards for MDR24/96 (3) AIO•8 cards for D8B (6) DB25 to DB25 analog snakes Hookup 1. Connect three snakes between the MDR24/96 Inputs (bottom connector) and the corresponding D8B Tape Outputs (top connector). 2. Connect three snakes between the MDR24/96 Outputs (top connector) and the corresponding D8B Tape Inputs (bottom connector). MDR24/96 Settings 1. Set the Sample Clock to Internal. 2. Set the Sample Rate and Bit Depth according to your preference. It is not necessary to set the D8B and MDR24/96 to the same Sample Rate, since with analog connections, the sample clocks on the two units are not synchronized Console Settings 1. Set the D8B Sample Clock to 44.1 k Internal or 48 k Internal according to your preference. Quick Start Guide Quick Start Guide 19 MDR 24/ 96 Note NoteNoteNoteNoteNote: Determining which unit in Figure1 provides the master clock depends on your application. For information on advanced applications, see the Applications Manual. TDIF Hookup (DIO•8) Cables & Hardware (3) DIO•8 cards for MDR24/96 (3) DIO•8 cards for D8B (1) Clock I/O card for D8B (3) TDIF cables (1) 75 . BNC word clock cable Hookup 1. Connect the three TDIF cables between the corresponding TDIF jacks on the MDR24/96 and D8B. 2. When TDIF is used, the D8B must have a Clock I/O card installed. To make the D8B the clock master, connect its Word Clock Out (not DIO•8 Sync out) to the MDR24/96 Word Clock In. To make the MDR24/96 the clock master, connect its Word Clock Out to the D8B Word Clock In. See Figure 1. MDR24/96 Settings 1. Set the Tape Input format for each DIO•8 card to TDIF, and the Tape Output format to TDIF. 2. If the MDR24/96 is the clock master, set the Sample Clock to Internal; if it is a clock slave, set it to Word Clock and depress the 75 . termination switch on the Sync card. 3. Set the Sample Rate to 44.1 kHz or 48 kHz according to your preference. Console Settings 1. Set the ...
Questo manuale è adatto anche per i modelli :DVD-Player - MDR 24/96 (1.85 mb)