valutazioni - 4, GPA: 5
(
)
)
|
Foto e specifiche Sony DVP-NS9100ES |
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
D-2 or D-3 : Connecting to a digital jack This connection will allow you to use the Dolby Digital, or DTS decoder function of your AV amplifier (receiver). z Hints • For correct speaker placement, refer to the instructions of the connected components. • To enhance the sound performance: –Use high-performance speakers. –Use front, rear, and centre speakers of the same size and performance. –Place the subwoofer between the left and right front speakers. Notes • When the i.LINK indicator lights up, audio signals are output from the i.LINK S200 AUDIO jack, but not from any of the other jacks (including HDMI OUT). Video signals are output from the HDMI OUT jack. For connection D-2 or D-3 • After you have completed the connection, be sure to set “DOLBY DIGITAL” to “DOLBY DIGITAL” and “DTS” to “DTS” in Quick Setup (page 32). • When you connect an amplifier (receiver) that conforms to the 96 kHz sampling frequency, set “48kHz/96kHz PCM” in “AUDIO SETUP” to “96kHz/24bit” (page 81). • Super Audio CD audio signals are not output from the DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT jack. • When you connect the player to an AV amplifier (receiver) using an HDMI cord, you will need to do one of the following: –Connect the AV amplifier (receiver) to the TV with the HDMI cord. –Connect the player to the TV with a video cord other than HDMI cord (component video cord, S VIDEO cord, or audio/video cord). • When the i.LINK indicator lights up, no signal is output from the DIGITAL OUT (COAXIAL or OPTICAL)/ HDMI OUT jack. Connecting to i.LINK components (TA-DA9000ES/STR-DA7100ES/ SCD-XA9000ES only) E Connect DVP-NS9100ES to i.LINK components (TA-DA9000ES/STR-DA7100ES/ SCD-XA9000ES only) with an i.LINK connecting cord. As of the date when this manual was published, this CD/DVD player is only compatible with i.LINK connections to the i.LINK components (TA-DA9000ES/STR-DA7100ES/ SCD-XA9000ES only). For details on i.LINK connections for future Sony components with i.LINK jacks, please refer to the Operating Instructions supplied with each component. Hookups E-1 : Connecting one receiver to an i.LINK jack CD/DVD player to i.LINK S200 (AUDIO) jack to i.LINK S200 (AUDIO) i.LINK connecting cord (not supplied) Receiver [Speakers] [Speakers] TA-DA9000ES STR-DA7100ES Front (L) Front (R) Centre Subwoofer Rear (L) Rear (R) l: Signal flow c continued E-2 E-2 : Connecting two players to a receiver’s i.LINK jacks CD/DVD player to i.LINK S200 to i.LINK S200 (AUDIO) i.LINK connecting cord (not supplied) to i.LINK S200 AUDIO OUT jack Player SCD-XA9000ES i.LINK connecting cord (supplied with SCD-XA9000ES) (AUDIO) jack [Speakers] [Speakers] STR-DA7100ES Receiver Front (L) Front (R) Centre Subwoofer l: Signal flow Rear (L) Rear (R) E-3 E-3 : Connecting a receiver and a player via this player (DVP-NS9100ES) CD/DVD player [Speakers] [Speakers] to i.LINK S200 (AUDIO) jack to i.LINK S200 (AUDIO) i.LINK connecting cord (not supplied) to i.LINK S200 AUDIO OUT jack i.LINK connecting cord (supplied with SCD-XA9000ES) Player SCD-XA9000ES Hookups STR-DA7100ES Receiver Front (L) Front (R) Centre Subwoofer l: Signal flow Rear (L) Rear (R) Note When the player is turned off or when the i.LINK indicator lights off, audio signals are not output from SCD-XA9000ES to STR-DA7100ES. c continued To use the i.LINK connection Press the i.LINK button in stop mode, so that the i.LINK indicator lights up on the player. To cancel the setting, press the i.LINK button again. Notes • i.LINK connections are only possible between this player and TA-DA9000ES/STR-DA7100ES/ SCD-XA9000ES. This player has some restrictions on i.LINK functions and may not operate properly if connected to components other than TA-DA9000ES/STR-DA7100ES/ SCD-XA9000ES. • Only component which inputs or outputs an audio signal using an i.LINK jack can be connected. Components using a video signal, PC component, and other AV amplifier cannot be connected to this player. • You cannot use the i.LINK connection when the player is turned off or when the i.LINK indicator lights off. • An audio signal of IEEE1394 components without the i.LINK mark cannot be used. • We do not guarantee playability when you connect a receiver, a DVD player, Super Audio CD/CD player, etc., from another company with i.LINK audio input or output jack. • If a metal object should fall into the i.LINK S200 AUDIO jack, short-circuiting may occur and damage the components. • Be sure to insert the plug firmly to prevent malfunction. • Some i.LINK components comply with copy protection technology and handle encrypted signals. This player complies with the DTLA copy protection technology (Revision 1.3). • “i.LINK“ lights up in the display when this player is ready to output the audio signals from the i.LINK S200 AUDIO jack. • When the i.LINK indicator lights up, audio signals are output from the i.LINK S200 AUDIO jack, but not from any of the other jacks (including HDMI OUT). • When you use the i.LINK connection, use a Sony i.LINK cable (not sup...