valutazioni - 2, GPA: 4
(
)
)
|
Foto e specifiche Sony DVP-FX870 |
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Hookups 39 Connecting to Video Player or Camcorder DC IN 9.5V AUDIO VIDEO PHONES OPTICAL OUTA B LINE SELECT IN OUT Video player or camcorder To AUDIO/VIDEO Audio/video cord (supplied) To AUDIO/VIDEO output To receive the playback signal from a Video Player or Camcorder 1 Set the LINE SELECT switch on the player’s right side to “IN.” Note Set the LINE SELECT switch to “OUT” after use. You cannot play back on the player if the switch is set to “IN.” Additional Information Additional Information Troubleshooting If you experience any of the following difficulties while using the player, use this troubleshooting guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer. Power The power is not turned on. , Check that the mains lead is connected securely. , When using with the battery pack, check that the battery pack is sufficiently charged. Picture There is no picture/picture noise appears. , The disc is dirty or flawed. , The brightness is set at minimum. Set the brightness in “LCD Mode” (page 28). , When you play discs, set the LINE SELECT switch to “OUT.” When you send the playback signal to other device, set the LINE SELECT switch to “OUT.” When you receive the playback signal from other device, set the LINE SELECT switch to “IN” (page 38). , Re-connect the connecting cord securely. , The connecting cords are damaged. , Check the connection to your TV (page 38) and switch the input selector on your TV so that the signal from the player appears on the TV screen. , The player is connected to the COMPONENT VIDEO IN (Y, PB, PR) jacks of high-vision TV. , If the picture output from your player goes through your video deck to get to your TV or if you are connected to a combination TV/VIDEO player, the copy-protection signal applied to some DVD programmes could affect picture quality. The picture does not fill the screen, even though the aspect ratio is set in “TV Display” under “General Setup.” , The aspect ratio of the disc is fixed on your DVD. The black points appear and the red, blue, green points remain on the LCD. , This is a structural property of the LCD and not mulfunction. Sound There is no sound. , The player is in pause mode or in Slow Play mode. , The player is in fast forward or fast reverse mode. , While playing a Super VCD on which the audio track 2 is not recorded, no sound will come out when you select “Stereo 1,” “Left 1,” or “Right 1.” , Re-connect the connecting cord securely. , The connecting cord is damaged. , The player is connected to the wrong input jack on the amplifier (receiver) (page 39). , The amplifier (receiver) input is not correctly set. , If the audio signal does not come through the OPTICAL OUT jack, check the audio settings (page 35). The sound volume is low. , The sound volume is low on some DVDs. The sound volume may improve if you set “Audio DRC” in “Audio Setup” to “TV Mode” (page 34). Operation The remote does not function. , The batteries in the remote are weak. , There are obstacles between the remote and the player. , The distance between the remote and the player is too far. , The remote is not pointed at the remote sensor on the player. , Direct sunlight or strong illumination is striking the remote sensor. Additional Information 41 Nothing happens when buttons are pressed. , The player’s \/1/HOLD switch is set on “HOLD” (page 16). The disc does not play. , The disc is turned over. Insert the disc with the playback side facing down. , The disc is not set correctly. , The player cannot play certain discs (page 7). , The region code on the DVD does not match the player (page 8). , Moisture has condensed inside the player (page 3). , The player cannot play a recorded disc that is not correctly finalized (page 7). , Parental Control has been set. Change the setting. , The LINE SELECT switch on the player’s right side is set to “IN.” The player starts playing the disc automatically. , The disc features an auto playback function. Playback stops automatically. , While playing discs with an auto pause signal, the player stops playback at the auto pause signal. Some functions such as Stop, Search, Scan, Slow Play, Repeat Play, or Random Play cannot be performed. , Depending on the disc, you may not be able to do some of the operations above. Refer to the operating instructions supplied with the disc. The language for the sound track cannot be changed. , Try using the DVD’s menu instead of the direct selection button on the remote (page 17). , Multilingual tracks are not recorded on the DVD being played. , The DVD prohibits the changing of the language for the sound track. The subtitle language cannot be changed or turned off. , Try using the DVD’s menu instead of the direct selection button on the remote (page 17). , Multilingual subtitles are not recorded on the DVD being played. , The DVD prohibits the changing of subtitles. The angles cannot be changed. , Try using the DVD’s menu instead of the direct selection...