valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Check the direction of the power connector and the drive incline before connection. Handle with caution to prevent damage from external shock. Any change or modification not expressly approved by designated qualified personnel could void your authority to operate this device. О Important to read and understand at all times Do not disassemble Warning/Caution _ Warning: To warn the user that failure to comply with the instructions may result in serious injury or death. Caution: To caution the user that failure to comply with the instructions may result in damage to property. A Do not drop the drive, and protect it fromsevere shocks. • It can damage the drive or cause it to malfunction. Do not move the drive while in operation and do not attempt to open the disc tray byforce. Make sure to close all working programs before attempting to open the tray and always use the open/close button. о Do not insert a pin into the emergency opening while in operation. Do not use cracked, distorted or damaged discs. Oin particular, a disc with a crack on the inner tracks may break while in use. A Never allow food particles or foreign substances to enter the drive casing. О To protect against the risk of fire, do ot spill such liquids as alcohol and benzene on the drive. Do not disassemble, attempt to repair or modify the device without express approval as directed in the manual. • To reduce the risk of damage, electric shock, and fire. 1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended that you make a copy immediately and use the copy instead. When a cracked disc s used continuously,the size of the crack is likely to grow and it will eventually result in irreparable damage to the disc. 2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs). 2 Introduction Design and specifications are subject to change without prior notice. Disc compartment Eject Button Front If the compartment does not open when you press the Eject button, power off the computer, insert a pin or unfolded paper clip in the hole and push firmlhy) Sound output terminal Interface terminal С terminal Accessories User Guide, Screw 4ea J The type of accessories varies depending on a product model. and some accessories described herein are subject to change without notice. * "40 Pin E-IDE cable and System requirements are available for 20X writing. But for Optimal 20X writing, 80pin E-IDE cable and Pentium IV 2.0GHz or faster are recommended." Connecting the Cables to the DVD Writer Connecting the Cables -"| Power cable 2 EIDE cable 3 Master/slave select terminal ■ 4 Audio cable 2 3 Connecting the power cable • The 4-pin power cable from the internal power unit of your computer must be connected to the power terminal the rear of the DVD Writer. Connecting the EIDE cable • Insert the EIDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) Installing a jumper on the master/slave select terminal • Connect a jumper to the rear side of the DVD Writer. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.) CS : Cable Select(CSEL) SL : Slave MA: Master 4 Connecting the EIDE cable from a sound card • Connect the 4-pin audio cable between the sound output terminal on the DVD Writer and the audio input terminal on the sound card. When using one EIDE cable • Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rear of the DVD Writer. When using two EIDE cable • Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rear of the DVD Writer. - If there is only one Optical drive: select MA (Master). -If there is two Optical drive, select MA (Master) / SL (Slave). Master Drive (Choose the MA Jumper) Slave Drive (Choose the SL Jumper) SEC 1 PRI 1 Hard Drive (Choose the MA Jumper) (Choose the SL Jumper) MainBoard Installing the Drive System Requirements Intel Pentium 800MHz(or higher) , 256MB of RAM (or higher) with an EIDE interface, Windows 2000/XP/Vista Installing the DVD Writer How to install the DVD Writer on your PC. First, remove the cover; connect the cable to the DVD Writer and then to the PC. 1 If necessary, attach a horizontal bracket to both sides of the drive. • You can purchase these accessories separately from your computer dealer. (Screws for use: M3 X 6 X 4) 2 Remove the plate from a free expansion slot and install the DVD Writer, as shown in the illustration. • If you have no free expansion slot, install the drive in place of the diskette drive. • Make sure to use the standardized screw...
Questo manuale è adatto anche per i modelli :DVD-Player - SH-S202N (839.25 kb)