valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
To connect a two channel digital stereo or A/V receiver with multi-channel decoder: 1 Connect one of the recorder’s DIGITAL AUDIO OUT jack (coaxial) to the corresponding in jack on your amplifier. Use an optional digital (coaxial) audio cable. 2 Activate the recorder’s digital output. (See “Audio Settings” on page 15). Digital multi-channel sound A digital multi-channel connection provides the best sound quality. For this you need a multi-channel audio/video receiver that supports one or more of the audio formats supported by your recorder, including MPEG 2, Dolby Digital and DTS. Check the receiver manual and the logos on the front of the receiver to verify this. Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” is a trademark of Digital Theater Systems, Inc. Accessory audio/video (A/V) connections To connect the recorder to an accessory component: • Connect the AV IN 1 or AV 2 IN jacks on the recorder to the audio/video out jacks on your accessory component, such as a VCR or camcorder, using the optional audio/video cables. (Refer to “Recording from DV input” on page 21.) Connecting a digital camcorder • Use a DV cable (not supplied) to connect the DV in/out jack of your DV digital camcorder to the front panel DV IN jack of your recorder. Note • If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all. • To play six-channel digital surround sound though a digital connection, your receiver must have a Digital Multi-channel decoder. • To see the audio format of the current DVD displayed on the screen, press AUDIO. • Your recorder does not perform internal (2-channel) decoding of a DTS sound track. To enjoy DTS multi-channel surround, you must connect your recorder to a DTS compatible receiver through one of your recorder’s digital audio outputs. L R DIGITAL INPUT AUDIO INPUT COAXIAL Digital coaxial cable Audio cable Note This jack is for connection to DV equipment only. It is not compatible with digital satellite tuners or D-VHS video decks. or Jack panel of component DV IN/OUT Front of recorder DV digital camcorder DV cable (not supplied) Remote control batteries The remote control requires two AAA (RO3) batteries (not included). We recommend that you replace the batteries on a yearly basis or when the operation of the remote control becomes intermittent or unsatisfactory. Replace the original batteries with new AAA batteries. Do not mix old and new batteries or different types of batteries. To replace the batteries: 1 Press the lock tab of the battery holder and open the battery compartment. 2 Place two AAA batteries in the battery holder, matching the + and – in the battery compartment. 3 Close the battery holder. Caution • Use only the size and type of batteries specified. • Make sure that you follow the correct polarity as indicated in the battery compartment. Reversed batteries may damage the device. • Do not mix different types of batteries together (for example, Alkaline and Carbon-Zinc) or old batteries with new ones. • If the remote is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. • Do not try to recharge batteries not intended to be recharged. They can overheat and rupture. Using your recorder Turning your recorder on and off To turn your recorder on and off: 1 Plug the power cord into the back of the recorder and into an electrical outlet. 2 Press the POWER button to turn on your recorder. 3 Press the POWER button again to turn off your recorder. Initial Setup Wizard The first time you turn on the recorder, the Initial Setup Wizard opens so you can set the language and clock. To set up your recorder with the Setup Wizard: 1 Use / to select a language for the Setup menu and on-screen display, then press ENTER. 2 Enter the necessary information for year, date, and time. • / (left/right): Moves the cursor to the previous or next column. • / (up/down): Changes the setting at the current cursor position. 3 Press ENTER to confirm your setting. 4 Press ENTER to exit the menu. Note You can reset the Initial Setup Wizard from the Factory Set option in the setup menu (see “General Settings” on page 15). Playing a tape To play a tape: 1 Press VCR to switch control to the VCR deck. 2 Insert a pre-recorded video cassette. • If the recorder is turned off, it turns on automatically when the tape is loaded. • If the Timer indicator lights on the front panel display window, press POWER once. 3 Press PLAY ( ) to start playback. If a tape without a safety tab is inserted, the recorder starts playback automatically. 4 Press STOP ( ) to stop playback. If the tape reaches the end before you press STOP ( ) the recorder automatically stops, rewinds, then ejects the tape. Note S-VHS Quasi Playback (SQPB) • Your recorder can play back S-VHS recorded ta...