valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Taladre un agujero en la pared, en el lugar donde desea colgar la campanilla. Si la esta instalando en una pared de mamposteria, utilice el tarugo de pared incluido. 2. Inserte el tarugo de pared en el agujero (si es necesario), luego atornille dejando la cabeza sobresaliendo 6 mm de la superficie. 3. Cuelgue la campanilla de modo que la cabeza del tornillo quede asentada en el agujero de la parte posterior (F), luego presione suavemente hacia abajo para que la campanilla no pueda deslizarse fuera de la cabeza del tornillo. Chime doesn’t sound when the bell push is pushed • Check that the batteries have enough charge and are installed the right way. Note the + and - symbols molded into the back of the battery compartment. • If the chime sound becomes faint or distorted, you should replace the batteries. Use LR14(C) alkaline batteries only. • Check that the bell push channel switch and the chime channel switch are in the same position. See Set Up. • Check that the distance between the bell push or the chime is not too great* (see front of pack). Chime sounds without being pushed • Check that there is not water in the bell push or the chime. This can damage the electronics. • Check that a neighbor is not using the same channel for their chime or a similar wireless system. See Set Up. *The stated transmission range if this product is measured in open field conditions. Walls, ceilings and metal structures (i.e. reinforced uPVC) will reduce the maximum range. Troubleshooting Test your wirefree door chime at the desired location before you mount the chime on the wall. 1. Press the bell push. 2. The chime should sound. Check the Troubleshooting section if the chime does not sound. Test Your Door Chime The chime is designed to be free standing or wall mounted, using a single screw (included). 1. Drill a hole in the wall where you want to hang the chime. If you are mounting to a masonry wall, use the wall anchor supplied. 2. Insert the wall anchor into the hole (if necessary), then screw in leaving the heads sticking out 6 mm from the surface. 3. Hang the chime so that the screw heads sit in the hole in the back (F), then press gently downwards so that it cannot slide off the screw head. Wall Mounting Portable Wireless Chime & Push Carillon et sonnette sans fil portatifs Campanilla inalambrica y pulsador portatil Portable Wireless Chime & Push RCWL100A RCWL100A RANGE distance 25 m25 m de alcance 75 ft WIRELESS sans filinalambrico CHIMES carillonscarillones3 COMPATIBILITY compatibilite compatibilidadA Please retain these instructions for future reference. • Bell Push • 75 ft. door chime • 3 screws, wall anchors, adhesive pad • 23A 12V Alkaline battery for the push Pack Contents • Small flat blade screwdriver • Small cross head screwdriver • 2 LR14(C) Alkaline batteries for the chime (not included) You Will Require 1. Open the bell push unit. Carefully insert a small flathead screwdriver into slot A and twist gently. Lift away the front of the bell push to reveal the inside. 2. Set the bell push channel. It is possible that your chime may be set off by a nearby wireless device. This could be a neighbor’s bell push, for example. To prevent this interference, you may need to change to another “channel”. Using a flat blade screwdriver, set rotary switch B to another position, 1 to 16. Make a note of the channel setting. Your chime will need to have its switch set to the same position – see “Set Up The Chime”. 3. Select a tune. Switch C, in the bell push, selects the chime tune: 1=Westminster 2=Ding Dong (manufacturer’s setting) 3=Ding Mount the bell push using the adhesive pad or by using the two screws, as follows: 1. Hold the bell push up against the door frame or wall where you want to mount it. (Ensure the push button is at the top). 2. Make a mark on the wall where the two screw holes will be. 3. Take away the bell push base and drill two holes, large enough to accommodate the wall plugs if necessary. 4. Screw the bell push to the wall through the mounting points D. 5. Insert the 12V 23A battery (included). 6. Refit the cover, locating the top catch first. Set Up The Bell Push Mounting The Bell Push 1. Set the chime channel. Set rotary switch E on the chime to position 1 to 16, as with the bell push. The channel set on the chime must match the channel already set on the bell push in “Set Up The Bell Push”. 2. Install the chime batteries. Remove the cover on the rear of the chime and insert the alkaline batteries, LR14(C), in the direction shown in the molding in the back of the battery compartment. Note that this door chime does not work with rechargeable Ni-Cd batteries. Set Up The Chime 1234 56789 101112 131415 16 1234 56789 101112 13141516 F E 1 2 3 23A 12V 1234 5 6 78910 111213 141516 A B C D ©2007 Honeywell International Inc. All Rights Reserved. Golden Valley, MN 55422 U.S.A. Engineered by Honeywell -Made in China Tous droits reserves. Concu par Honeywell -Fabrique en Chine Todos los derechos reservados. Disen...