valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
• If battery is swallowed, immediately notify doctor. 1. Install alkaline type A23 12 volt push button battery (included). Remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). See diagram inside push button for correct battery orientation. Note: If batteries are preinstalled, remove orange battery tab. 2. Plug in wireless chime. To reduce the risk of electrical shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not attempt to bypass this safety feature. 3. Test range. Temporarily position push button where you want it mounted. Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. Figure 1 © 2008 HeathCo LLC 595-5684-09 595-5684-09 -2- 4. Adjust volume control (Available on selected chimes). Unplug chime and adjust volume control to desired volume (see Figure 2). Plug chime back into wall outlet. 5. Mount push button. Use either screws or double sided tape to mount push button. • Screw Mounting: To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver (see Figure 1). Note: Remove material in screw holes (if needed) before mounting with screws. Attach back of case to door jamb or wall (see Figure 3). Snap front of push button on. • Tape Mounting: When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. Chime Volume Control (Selected Chimes) Jumper Access Door (See Tune or Code Section) Figure 2 Figure 3 595-5684-09 -3- Tune Settings WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. Your wireless chime has different selectable tunes: Ding (one note), Ding-Dong (two note), or Westminster (eight note) (Available on selected chimes). The factory setting is for the Ding-Dong tune (or Westminster, when available). This tune can be changed by following the instructions below. • Ding (one note tune) Inside Push Button: Add a jumper to location 8. • Ding-Dong (two note tune) Inside Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Inside Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note: All models have both front and back door tune capabilities. We recommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come factory set for front and back doors. Decals on the rear of the push button will indicate its setting. Remove screw to open access door 1 2 3 4 5 6 7 8 12345678 Tune Setting Tune Setting (Not used on all models) Inside Push Button Note: Some models might require the use of tweezers to remove and replace the jumpers. Back of Chime Figure 4 Troubleshooting A. Chime does not sound: • Make sure push button and chime codes are the same (see Figure 5). • Check orientation of push button battery (See diagram inside push button for correct battery orientation.) • Check charge of push button battery, replace if necessary. • Make sure the plug-in chime has power going to it. B. Chime sounds when not intended (false triggers): Chime is receiving interference from another wireless device; change the code setting (see Code Setting below). C. Batteries seem OK, but the chime does not work when installed: • Do not mount chime or push button on metal or near metal studs. This reduces the transmitter range. Use 1/4" to 1/2" (6 to 13 mm) wood shims to move chime or push button off metal surface. • Concrete floors may reduce range. Move chime away from floor. • Try locating chime closer to push button. D. Code Setting: It is recommended to only change one code position at a time and then check to see if system is functioning properly. 1. Unplug chime from power source. 2. Open the cases and locate the jumpers on both the push button and chime (see Figure 5). 3. The push button and chime both have eight different jumper locations. Jumper positions 1 through 7 are used for setting the code. WARNING: Disconnect chime unit from power source before opening code access door. Close door and replace screw before reconnecting to power. 4. To change the code, either (For models with 2 push buttons, change code setting in both push buttons to match chime.): • Add a jumper to the same location on both the push button and the chime or... • Remove a jumper from the same location on both the push button and the chime or... • Move a jumper on the push button from one location to another. Move the corresponding jumper on the chime to match the new location in the push button. Example: Move jumper a...