valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
Press the MENU button. 2 Use the [Review]. and buttons to select 3 Use the or [Off]. and buttons to select [On] • Press the MENU button to close the menu. Review Feature When the review feature is set to On, the photographed image will show in the LCD monitor if you continue to hold the shutter button down fully after recording. If you press the SET button at this point, the image will continue to display in the LCD monitor even if you release the shutter button. You can also erase the image immediately if you wish (p. 60). Cancel the review feature by pressing the shutter button halfway. Resetting the File Number Select the way image file numbers are assigned with this feature. On: The next file number assigned is reset to the initial value (100-0001) each time a new CF card is inserted. Images recorded onto a CF card containing existing images are assigned the next available file number on that card. Off: The last assigned file number is stored and the next available file number is assigned to an image recorded on any CF card, including a new CF card. 1 Turn the Mode Dial to the , , or position. Press the MENU button. 2 Use the No. Reset]. and buttons to select [File 3 Use the or [Off]. and buttons to select [On] File Number Conventions A photographed image is assigned a number ranging from 0001 to 9900 and stored in a folder containing up to 100 files. The folders are assigned numbers ranging from 100 to 998. 0099 0100 100 0001 0002 Shooting 101 0101 0102 0199 0200 198 9801 9802 9899 9900 • Press the MENU button to close the menu. Folder numbers cannot contain 99 in the last two digits. 200 0001 0002 0099 0100 • Images shot in continuous or Stitch Assist mode are always kept in the same folder, which may result in some folders containing 101 or more files. • Recording with the File No. Reset option set to Off is convenient when the image files are downloaded to a computer because duplicate file names can be avoided. Replaying Magnifying an Image (Single Image Replay) 1 Turn the Mode Dial to the position. 2 Press the button. Approximate position within the image. • You can use the , , and buttons to shift the display within the image. • Press the button again to end the magnification mode. • The currently displayed image can be deleted by holding the SET button down and pressing the button. (p. 60) This section explains the various replay features, including how to magnify and rotate the image in the LCD monitor or show images in slide shows. It also discusses DPOF print settings. Rotating an Image 1 Turn the Mode Dial to the position. Press the MENU button. 2 Use the and buttons to select [Rotate]. Press the SET button. • Subsequently, the image will rotate clockwise to the next orientation (90°, 270° and 0°) each time the SET button is pressed. 0° (Original) 90° 270° • Press the MENU button to end the Rotate feature. • Rotating images in the display has no effect on the recorded images. Jumping Images The display can be jumped forward or back. 1 Turn the Mode Dial to the position. 2 Press the JUMP button. Single Image Replay • Press the or button to jump to the tenth image ahead or behind. • Press and hold the SET button and press the or button to jump to the first or last image. Multi Image Replay • Press the or button to jump to the next set of 9 images ahead or behind. • Press and hold the SET button and press the or button to jump to the first or last set of 9 images. • Press the JUMP button again to end the Replaying jump feature. Viewing Image Information 1 Turn the Mode Dial to the position. 2 Press the DISPLAY button. • The LCD monitor will cycle to the next display mode (simple, detail, non display) each time the DISPLAY button is pressed. The detail display is not available in multi image replay mode. • The following information is shown in the simple display mode. -File number; Shooting date/time; Protection status ( ). • The following information is also shown in the detailed display mode. -Image mode ( , , , , ) -Macro mode ( ) -Shooting methods ( , , ) -Flash ( , ) -Exposure compensation ( ) -White balance ( , , , , ) -Compression ( , , ) -Resolution ( , , ) -Stitch Assist mode status Automated Playback (Slide Show) Starting a Slide Show You can start a slide show with the following procedures. All Images: displays all images on the CF card in order Show 1 - Show 3: displays the images selected for the respective slide show in order 1 Turn the Mode Dial to the position. Press the MENU button. 2 Use the and buttons to select the [Slide Show]. Press the SET button. 3 Use the and buttons to select [Program]. 4 Use the and buttons to select [All Images], [Show 1], [Show 2] or [Show 3]. 5 Use the , , and buttons to select [Start]. Press the SET button. The slide show will start. • Press the SET button to pause or restart it. • When a slide show is paused, or the Play Time is set to Manual, you can use the and buttons to view the previous or next slide. • Press the MENU button to stop a slide sh...