valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
Removing Memory Cards Memory cards can be removed without loss of data when the camera is off. To remove memory cards, turn the camera off and confirm that the power-on lamp is off. Do not open the memory card slot cover while the power-on lamp is lit. Open the memory card slot cover and press the memory card to partially eject the card. The card can then be removed by hand. Memory Cards • Use only Secure Digital (SD) memory cards. • Do not disassemble or modify. • Do not drop, bend, or expose to water or strong physical shocks. • Do not touch the metal terminals with your fingers or metal objects. • Do not affix labels or stickers to the memory card. • Do not leave in direct sunlight in a closed vehicle or in other areas exposed to high temperatures. • Do not expose to high levels of humidity or to corrosive gas. The Write Protect Switch First Steps SD cards are equipped with a write protect switch to prevent accidental loss of data. When this switch is in the “lock” position, pictures or sounds can not be recorded, deleted, or edited, and the card can not be formatted. Do not lock the card when recording, deleting, or editing pictures or sounds. Write protect switch When card is locked, pictures or sounds can be played back but can not be recorded, deleted, edited, or transferred using the camera I (V) button. 11 Checking the Battery Level Turn the camera on • Press the power switch. The power-on lamp will light. Rotate the mode dial to a setting other than f. 1Checking the Battery Level Turn the camera on • Press the power switch. The power-on lamp will light. Rotate the mode dial to a setting other than f. 1 77AUTOAUTO7M7M 2 2 Check the battery level in the monitor • When the camera is turned on for the first time, a language selection dialog will be displayed. Choose the desired language and press I (the center of multi selector). See “First Steps: Basic Setup” (Q 14). • Before checking the battery level, select the appropriate Battery type option in the SETUP menu (Q 111). Display Meaning NO ICON Batteries fully charged. X Low battery. WARNING!! BATTERY EXHAUSTED Batteries exhausted. Replace with new or fully charged batteries. The red (!) and green (AF) lamps will blink when the “BATTERY EXHAUSTED” warning is displayed. First Steps The x Button The camera can also be turned on by pressing the x button for about a second. Your most recent picture will be displayed in the monitor (Q 22). 12 Checking the Battery Level Turning the Camera Off Checking the Battery Level Turning the Camera Off To turn the camera off, press the power switch when the power-on lamp is lit. Do not remove the batteries or disconnect the EH-62B AC adapter until the power-on lamp has gone out. The Power-on Lamp When the power on lamp is The camera is On On Blinking In standby mode Off Off Auto Power Off (Standby Mode) If no operations are performed for one minute (default setting), the monitor will turn off automatically and the camera will enter standby mode to reduce the drain on the batteries. While the camera is in standby mode, the power-on lamp will blink. If no operations are performed for three minutes after the camera enters standby mode, the camera will turn off automatically and the power-on lamp will go out. The camera will be reactivated from standby mode when you: • Press the power switch • Press the shutter-release button halfway • Press the x button to view the last picture taken • Press ^ button to display the menu for the current mode • Rotate the mode dial to select a new mode The length of time before the camera enters standby mode can be changed using the Auto off option in the SET-UP menu (Q 105). However, when a menu or the SET-UP menu is displayed, the monitor will turn off after three minutes, and when pictures are being shown in a non-stop slide show (Q 88) or when the camera is powered by an AC adapter, the monitor will turn off after thirty minutes. Sleep Mode First Steps Turning sleep mode on will cause the camera to enter standby mode when there is no change in the brightness of the subject, even before the time selected in the AUTO OFF menu has elapsed (Q 105). 13 Basic Setup The first time the camera is turned on, a language-selection dialog will be displayed in Basic Setup The first time the camera is turned on, a language-selection dialog will be displayed in the monitor. Follow the steps below to choose a language and set the time and date. First Steps 1Highlight Deutsch (German), English, Espanol (Spanish), Francais (French), Italiano (Italian), Nederlands (Dutch), (Russian), Svenska (Swedish), (Japanese), (Simplified Chinese), (Traditional Chinese) or (Korean) and press I (the center of the multi selector). 2Select No to exit to mode currently selected with mode dial. If you exit without setting time and date, Z (“date not set”) icon will flash in monitor when camera is in shooting mode and all pictures will have time stamp of “0000.00.00 00:00” (still images) or “2005.01.01 00:00” (movies). Hi...