valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
This shortens the operating time of the battery to less than the normal time. • Do not pick up the camcorder by this unit. On cleaning Clean the video light with a dry soft cloth. You can remove stubborn stains with a cloth lightly dampered with a mild detergent solution, then dry the unit with a soft cloth. Never use strong solvents, such as thinner, benzine or alcohol, since these will damage the finish on the surface. Specifications Power requirements 7.2 V DC Power consumption Approx. 3.0 W Maximum luminous intensity Approx. 100 cd Lighting direction Horizontal Lighting angle Approx. 15 degrees Continuous lighting time Lighting duration Type of battery pack Used with camcorder (DCR-HC90)* NP-FA50 35 (30) NP-FA70 70 (60) (Approx. minutes using fully-charged battery pack) * When used with the LCD panel closed. Duration with the LCD panel open is shown in parentheses. Illumination range Approx. 1 m (3 1/4 ft) : 100 lux, Approx. 2 m (6 1/2 ft) : 25 lux, Approx. 3 m (9 3/4 ft) : 12 lux Color temperature Approx. 3,000 K Average life of lamp Approx. 100 hours Otmhers Dimensions Approx. 31.5 . 57.5 . 40 mm (1 1/4 . 2 3/8 . 1 5/8 inches) (w/h/d) Mass Approx. 30 g (1.1 oz) Included items Video light (1) Pouch (1) Set of printed documentation Design and specifications are subject to change without notice. AAttaching or removing the video light to a camcorder Set the power switch of the video light to OFF before attaching or removing it from the camcorder. To attach the video light 1 Make sure that you completely turn the lock knob counterclockwise1. 2 Align the arrow on the rear of the video light2 with the arrow on the camcorder3. 3 Attach the shoe connector (terminal) of the video light to the concave part of the camcorder4, and then slide the video light in the direction of the arrow3. 4 Turn the lock knob clockwise until it clicks into place. 5 Turn the video light to the same direction as the camcorder lens. The video light can be rotated more than 180 degrees. To remove the video light 1 Loosen the lock knob by turning it counterclockwise in the opposite direction of the arrow. 2 Push down and pull out the video light in the opposite direction of the arrow to remove it. Note If you cannot insert the video light, turn the lock knob counterclockwise until it reaches the end to cancel the lock. BUsing the video light To turn on the video light automatically in a dark place 1 Set the power switch to AUTO. 2 Set the camcorder to standby mode. The video light turns on automatically when using the camcorder in a dark place. In AUTO mode, the video light is turned off automatically after about 5 minutes even during recording. To turn off the video light when the light is on, switch the camcorder to OFF (CHG), or switch the video light to OFF. To turn on the video light for the entire recording time, switch the video light to ON. To control the video light with the camcorder in standby mode 1 Set the power switch to ON. 2 Set the camcorder to standby mode. The video light is turned on in sync with the camcorder. To turn off the video light, switch the camcorder to OFF (CHG), or switch the video light to OFF. After use Set the power switch to OFF. Notes • The battery discharges while the camcorder is in standby mode. Be sure to switch from standby to OFF (CHG). • Store in pouch when not in use. • Make sure the video light has cooled down before storing it. CLighting up a subject • When recording indoors with this unit, you can get clear and beautiful color pictures. • For wide angle shots, the video light may not light the corners of pictures completely. Use the video light for shooting the main subject of the picture effectively. • Fluorescent lights tend to produce flickering in the recording. Use of the video light may help to produce better pictures with less color blur. DReplacing the lamp Use the Sony XB-3L xenon lamp. Consult your Sony dealer or local authorized Sony service facility for replacement of xenon lamp XB-3L. Order the following parts number when purchasing the xenon lamp : A- 1099-823-s. The lamp is hot when it has just burned out. Wait until the lamp cools down before removing it. 1 Remove the front cover by inserting someting like a coin after making sure that the unit is cool enough to handle. 2 Replace the lamp. 1 Cover the old lamp with the tube supplied with the new lamp for replacement and pull the tube out to replace the old lamp. 2 Insert the new lamp into the socket straightly. * Do not tilt the lamp. 3 Insert the pawls on the front cover and attach it. Notes • The lamp is hot when it has just burned out. Make sure that the lamp is cool enough to handle. • To prevent the lamp from being smudged with fingerprints, handle it with a dry cloth. If the lamp is smudged, wipe it completely clean. . 2005 Sony Corporation Printed in Japan Video Light Lampe video HVL-HL1 2-515-130-12(1) Operating Instructions Mode d’emploi Manual de instrucciones Istruzioni per l’uso Francais Ce label indique le sys...