valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Before attaching the ring light For details on compatible camera models of this unit, visit the Sony website in your area, or consult your Sony dealer or local authorized Sony service facility. Check the operating instructions of your lens for the diameter of the adaptor ring. .. Remove any accessories attached to the camera*, such as a lens hood or filter. * like the Interchangeable Lens Digital Camera, video camera etc. .. Remove the front lens cap from the lens. Attaching the ring light (See illustration .) 1 Firmly attach the adaptor ring that has the same filter diameter as the lens. (Illustration .) 49 mm and 55 mm diameter adaptor rings are supplied with this ring light. 2 Slide the mounting foot of the Shoe Adaptor all the way into the Accessory Shoe of the camera. 3 Firmly attach the operating part to the Accessory Shoe of the Shoe Adaptor. (Illustration .) 4 Attach the ring part to the adaptor ring. (Illustration .) *Attach the ring part with its release button at the top. Note Be careful not to scratch the lens when attaching the adaptor ring. Removing the ring light 1 Remove the ring part from the adaptor ring by pushing the release button. 2 Remove the operating part from the Accessory Shoe of the Shoe Adaptor. 3 Hold down the lock release of the Shoe Adaptor and slide the Shoe Adaptor out of the Accessory Shoe of the camera. 4 Remove the adaptor ring. Using the ring light For details, refer to the Operating Instructions of your camera. 1 Set the POWER switch of the camera to “ON.” 2 Set the POWER switch of the operating part of the ring light to “ON.” 3 Point the camera at the subject and shoot. When the ring light is attached to the camera, the weight of the lens part makes it unstable. We recommend using a tripod or supporting the lens firmly with one hand. Notes .. When reproducing true colors, select the custom white balance mode of the camera. Reset the white balance if you have changed the BRIGHT dial of the operating parts. Refer to the operating instructions of your camera for how to change the settings. .. Do not pick up the camera by the ring light attached. The camera may fall. .. When shooting a highly reflective subject, the reflection of the ring light may appear in the image. Switches and lighting of the ring light (See illustration .) .. You can change the illumination intensity with the BRIGHT dial of the operating part. The illuminance of the ring light can be adjusted between 100% (MAX) and 10% (MIN) using the BRIGHT dial. .. After the battery end, the ring light may light up again when you set the POWER switch to “ON.” This is not malfunction. Meaning of POWER lamp states .. When it lights (green) Batteries have sufficient power. .. When it flashes slow (red) (Battery Pre-End) Prepare new batteries. * The flashing time changes depending on the battery type being used. .. When it flashes fast (red) (Battery End) The ring light is put out. The batteries are run down. Replace with new batteries. Caution This unit does not have dust-proof, splash-proof or water-proof specifications. .. Do not look at the LED light unit directly at close range while it is on. It may damage your eyes. .. Do not place the ring light near combustible or volatile solvents, such as alcohol or benzine. Doing so may cause a fire or smoke. .. The LED light unit and parts around it may get hot and burn you. .. When the ring light is used in low-temperature conditions, battery performance is reduced. For example, lighting time becomes shorter than at room temperature (about 25 °C) and charging time becomes longer. We recommend having new spare batteries available. However, batteries whose performance has dropped due to low temperature are restored when they are returned to room temperature. .. Do not leave or store the ring light in temperatures exceeding 60 °C. Doing so may harm the internal structure of the ring light. (Take particular care not to leave the ring light in a car during summer.) .. A camera placed on a table with the ring light attached will be unstable. Handle carefully. .. Do not pick up the camera by the ring light attached. The camera may fall. .. Do not pull the cable connecting the ring part and operating part. This cable is fixed. Cleaning Remove the ring light from camera. Clean the ring light with a dry soft cloth. In case of stubborn stains, use a cloth lightly dampened with a mild detergent solution, then wipe the unit clean with a dry soft cloth. Never use strong solvents, such as thinner, benzine or alcohol, as these damage the surface finish. Troubleshooting Symptom Remedy The ring light does not work. .. Make sure that the POWER switch of the ring light is “ON.” .. Confirm the ., . poles of the batteries. .. Replace with new batteries. .. Contact a Sony dealer (Sony service facility). The ring light turns off too quickly. .. When using the ring light at low temperatures, warm the batteries first. * The battery life of alkaline batteries is about 40 minutes and the battery li...