valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Continued operation could result in injury. After removing or disconnecting the power source, take the equipment to a Nikon-authorized service representative for inspection. Do not use the camera or lens in the presence of flammable gas If the electronic equipment is operated in the presence of flammable gas, it could result in an explosion or a fire. Do not look at the sun through the lens or viewfinder Viewing the sun or other strong light sources through the lens or viewfinder could cause permanent visual impairment. Keep out of reach of children Particular care should be taken to prevent infants from putting the batteries or other small parts into their mouths. Observe the following precautions when handling the camera and lens • Keep the camera or lens unit dry. Failure to do so could result in a fire or electric shock. • Do not handle or touch the unit with wet hands. Failure to do so could result in electric shock. • When the lens will not be used for a long time, attach both front and rear lens caps and store the lens away from direct sunlight. Failure to do so could result in a fire, as the lens might focus sunlight onto an object. Major features • This is a high-grade, internal focusing (IF) lens employing a Silent Wave Motor to drive the focusing mechanism, thus the “S” designation. As a result, autofocusing is smooth, silent, and almost instantaneous. • With this lens, you can take pictures at shutter speeds approx. 4 stops* slower than you ordinarily could without using a VR lens, expanding the range of usable shutter speed options and making telephoto shooting much easier without a tripod. *Under Nikon measurement conditions • Autofocus (A) or manual (M) mode can easily be selected with the focus mode switch. • Autofocusing with manual override is provided, allowing instant change from autofocusing to manual focusing. • More accurate exposure control is possible when this is mounted on a Nikon camera having 3D Matrix Metering capability, because subject distance information is transferred from the lens to the camera body. Focusing, zooming, and depth of field First turn the zoom ring 5 until the desired composition is framed in the viewfinder before focusing. If your camera has a depth of field preview (stop-down) button or lever, depth of field can be observed while looking through the camera viewfinder. • By using Internal Focusing (IF), the closest focusing distance of this lens is shorter than previous models at the same focal length, which utilized traditional helicoid focusing. Focusing Set your camera’s focus mode selector according to this chart: Autofocus with manual override (M/A mode) 1 Set the lens focus mode switch % to M/A. (Fig. A) 2 Autofocus is provided, but you can manually override the focus by operating the separate focus ring while lightly depressing the shutter release button or AF start (AF-ON) button on the camera body of cameras so equipped. 3 Remove your finger then press the shutter release button lightly or the AF start button once again to cancel manual focus and resume autofocus. Getting good results with autofocus Refer to “Notes on using wide or super-wide angle AF Nikkor lenses” on the back of this sheet. Vibration reduction mode (VR.) Basic concept of vibration reduction Setting the vibration reduction ON/OFF switch (Fig. B) ON: Vibration is reduced while the shutter release button is lightly pressed and also at the instant the shutter is released. Because vibration is reduced in the viewfinder, auto/ manual focusing and exact framing of the subject are easier. OFF: Vibration is not reduced. Setting the vibration reduction mode switch (Fig. C) NORMAL: The vibration reduction mechanism primarily reduces camera shake, making smooth panning shots possible. ACTIVE: The vibration reduction mechanism reduces camera shake when taking pictures and those from a moving vehicle. In this mode, the lens does not automatically distinguish panning from camera shake. Notes on using vibration reduction • Wait until the image in the viewfinder stops vibrating before fully depressing the shutter release button after you have lightly pressed the shutter release button. • When taking panning shots, be sure to set the vibration reduction mode switch to NORMAL. If you move the camera in a wide arc when panning, vibration in the direction of that movement is not affected. For example, if you pan the camera horizontally, only vibration in the vertical direction is reduced, making smooth pans much easier. • Due to the characteristics of the vibration reduction mechanism, the image in the viewfinder may become blurred after releasing the shutter. • Do not turn the camera power OFF or remove the lens from the camera while the vibration reduction mode is in operation. (Otherwise, the lens may emit a chattering noise if the camera is shaken. This is not a malfunction. Turn the camera power ON again to correct this.) • With cameras (such as the D70-Series and D50) featuring a built-in flash...