Log:
valutazioni - 2, GPA: 4 ( )

Istruzioni per l'uso Echo, Modello PE-225

Produttore : Echo
File Size : 901.14 kb
File Nome : PE225es1112_092810.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


4. Loosen adjustment knob and adjust the blade's depth of cut toproduce a fine cut between sidewalk and grass using a minimumblade depth, usually with about 13 mm (1/2 in.) of the blade intothe ground. Tighten adjustment knob. 5. Before edging, plan your direction of travel so that the unit will always be positioned on your right side and so that you walk on a hard surface whenever possible. 6. Hold edger as shown. warningBefore edging, be sure to read and understand the entire Operator's Manual to avoid the chance of serious injury. 7. When starting to edge, run the engine at full throttle, and lower the blade gently into the ground, being careful not to hit the concrete with the blade. 8. Don't force the blade. Move as quickly as the blade will allow. warningThe complete unit, specifically the drive shaft assembly and muf- fler exhaust area may become very hot during use. Avoid contact during and immediately after operation, otherwise serious personal injury may result. inCrEaSE DEPTH wHEEL aDJUSTMEnT KnOB DECrEaSE DEPTH 1/2 in. warningEngine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconscious- ness, serious injury, or death. Exhaust can cause serious burns. ALWAYS position unit so that exhaust is directed away from your face and body. operatIng technIques maIntenance warning Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces. Your ECHO edger is designed to provide many hours of trouble free service. Regular scheduled maintenance will help your edger achieve that goal. If you are unsure or are not equipped with the necessary tools, you may want to take yourunit to an ECHO Service Dealer for maintenance. To help you decide whether you want to DO-IT-YOURSELF or have the ECHO Dealer do it, each maintenance task has been graded. If the task is not listed, see your ECHO Dealer forrepairs. skIll level Level 1 = Easy to do. Common tools may be required. Level 2 = Moderate difficulty. Some specialized tools may be required. ECHO offers rEPOWErTM Maintenance Kits and Parts to make your maintenance job easier. maIntenance Intervals COMPONENT / SYSTEM MAINTENANCE PROCEDURE REQ'D SKILL LEVEL DAILY OR BEFORE USE EVERY REFUEL 3 MONTHS OR 90 HOURS YEARLY 600 HOURS Air Filter Inspect/Clean 1 I / C * R* Choke Inspect/Clean 1 I / C Fuel Filter Inspect 1 I * I / R * Fuel Cap Gasket Inspect/Replace 1 I * R * Fuel System Inspect/Replace 1 I (3) * I (3) * Spark Plug Inspect/Clean 1 I / C / R * Cooling System Inspect/Clean 2 I / C Muffler Spark Arrestor Inspect/Clean/Replace 2 I / C / R * Cylinder Exhaust Port Inspect/Clean/Decarbon 2 I / C Drive Shaft Grease 2 I (1) Gear Housing Grease 2 I (2) Blade Replacement Inspect/Replace 1 I I I * Recoil Starter Rope Inspect/Clean 1 I / C * Screws/Nuts/Bolts Inspect/Tighten/Replace 1 I * (2) Apply POWER BLENDXTM grease every 15 - 25 hours of use. (3) Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity. * All recommendations to replace are based on the finding of damage or wear during inspection. MAINTENANCE PROCEDURE LETTER CODES: I = INSPECT, R = REPLACE, C = CLEAN IMPORTANT NOTE - Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. MAINTENANCE PROCEDURE NOTES: (1) Apply POWER BLENDXTM grease every 25 hours of use. aIr fIlter Level 1. Parts required: REPOWERTM AIR & FUEL FILTER KIT. 1. Close choke (Cold Start Position [ ]). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover. Brush dirt from inside cover. 3. Remove air filter and lightly brush debris from filter. Replace filter if it is damaged, fuel soaked, very dirty, or the rubber sealing edges are deformed. 4. If filter can be reused, be certain it: • Fits tightly in the air filter cavity. • Is installed with the original side out. 5. Install air filter cover. fuel fIlter Level 1. Parts required: REPOWERTM AIR & FUEL FILTER KIT. DangEr Fuel is VEry flammable. Use extreme care when mixing, storing or handling. 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Use the “fuel line hook” to pull the fuel line and filter from the tank. 3. Remove the filter from the line and install the new filter. nOTE Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank. When servicing model year 2012 and later equipment, only fuel supply hoses cert...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie