valutazioni - 0, GPA: 5
(
)
)
|
Foto e specifiche Flymo ROLLER COMPACT 400 |
Facilità d'uso
Removing and Fitting the Blade and Fan (Q) Q blade blade bolt fan pulley Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade and Fan 1. To remove the blade bolt, hold the fan firmly and, with the spanner provided, loosen the blade bolt by turning it anti-clockwise. 2. Remove the blade bolt, blade and fan from the pulley. 3. Inspect for damage and clean as necessary. Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one. Fitting the Blade and Fan 1. Ensure the fan is located correctly. 2. Fit the blade to the fan. 3 Re-assemble blade bolt through blade and fan. 4. Hold the fan and tighten blade bolt firmly with the spanner provided. Do not over tighten. R1 R2 R3 R4 Storing your cable in the Easi-Reel cable winder 1. Insert the femaleconnector into the top of the cable winder (R1) 2. Place the cable under the cable guide (R2) 3. Turn the cable winder (R3) until all of the cable is wound in.(R4) Unwinding the cable before re-use 1. Pull the cable by the plug and unwind the cable fully. • Ensure that the cable is released from the cable guide (R2) before using your machine. Easi-Reel Cable Winder (Roller Compact 4000 only) T V Caring for your Lawmower Cleaning (S) S • USE GLOVES • IMPORTANT: It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. • IMPORTANT Never use water for cleaning your lawnmower. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. 1. Remove grass from under the deck with the spanne/scraper tool 2. Remove the blade, see Figure Q, to gain access to the fan and clean with a soft brush. 3. Raise the roller to its highest position, see Cutting Height Adjustment, and clean with a soft brush. 4. Remove grass clippings from: all air intakes, wheels, height adjustment lever and grassbox with a soft brush. 5. Clean the grassbox lid and the inside of the window with a soft brush. 6. Thoroughly clean around the cut-out switch with a soft brush 7. Wipe over the surface of your lawnmower with a dry cloth. Cleaning Easi-Reel cable winder (Roller Compact 4000 only) 1. Lift grassbox lid, squeeze together the two catches (T) and remove the cable winder. 2. Clean the cable winder and the area it was located with a soft brush (V) 3. Replace the cable winder, ensuring it clicks into place. At the End of the Mowing Season 1. Replace blade, bolts, nuts or screws, if necessary. 2. Clean your lawnmower thoroughly. 3. Ask your local Service Centre to clean the air filter thoroughly and carry out any service or repairs required. 4. Make sure that the electric cable is wound properly. Storing the lawnmower The handles can be folded to take up the minimum of space. • Loosen the handle knobs • Fold the upper handle over the lawnmower. • Ensure the switchbox cable is not trapped. • Store in a dry place where your lawnmower is protected from damage. Fault Finding Hints Fails to Operate 1. Is the correct Starting procedure being followed? See ‘To Start your Lawnmower’. 2. Is the grassbox lid firmly closed? 3. Is the Power Turned On? 4. Check the fuse in the plug, if blown replace. 5. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local approved Electrolux Outdoor Products Service Centre. Poor Grass Collection 1. Disconnect from the mains electricity supply. 2. Check that the grass chute and the underside of the deck are free from grass. 3. Raise to a higher height of cut. See Cutting Height Adjustment. 4. Clean Fan Blades. 5. If poor collection persists. Immediately disconnect from the mains electricity supply and consult your local approved Electrolux Outdoor Products Service Centre. Lawnmower becomes heavy to push 1. Disconnect from the mains electricity supply. 2. In long grass or uneven ground, the height of cut should be raised to a higher position. See Cutting Height Adjustment 3. Check that the wheels and roller can rotate freely. 4. If problem persists? Immediately disconnect from the mains electricity supply and consult your local approved Electrolux Outdoor Products Service Centre. Excessive Vibration 1. Disconnect from the mains electricity supply. 2. Check that the blade is fitted correctly? 3. If the blade is damaged or worn, replace it with a new one. 4. If vibration persists, turn the blade through 180o by first loosening the blade bolt, turning the blade and re-tightening the blade bolt. 5. If vibration persists? Immediately disconnect from the mains electricity supply and consult your local approved Electrolux Outdoor Products Service Centre. Environmental Information Electrolux Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally respon...