Log:
valutazioni - 4, GPA: 4.5 ( )

Istruzioni per l'uso Agri-Fab, Modello 45-03622

Produttore : Agri-Fab
File Size : 3.65 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


4 OPERATION HAIR COTTER PINTRACTORHITCH PINOR MOWERCLEVIS PINREMOVE MOWER CLEVISPIN FROM THIS HOLE FIG. 5 OPERATION OPERATION GROUND LEVELCUTTING HEIGHTCUTTINGHEIGHTSHEIGHT ADJUSTMENT STRAPHEIGHT ADJUSTMENTLIFT LEVERLOCATING PINHAIR COTTER PINCLEVIS PINTOW BARADJUSTMENTTOW BARHAIR COTTER PIN1-1/2" 2" 2-1/2" 3" 3-1/2" 4" 4-1/2" 5" FIG. 6 OPERATION This mower has been designed to run offset from the center of the tow vehicle. This allows the operator to drive along side high brush with the tow vehicle while cutting down the brush beside him. The adjustable hitch gives you three offset cutting positions plus straight behind for narrow paths. MODEL 45-0362 The adjustable hitch of this mower can be set in seven positions including straight and offsets of 9", 17" and 23" on both sides. (See Fig. 7) CUSTOMER RESPONSIBILITIES WHEEL 2WHEEL PIVOT 3QUADRANT 3SPINDLE 2SWIVEL 2WHEEL PIVOT 3WHEEL 2 CUSTOMER RESPONSIBILITIES BLADE CARE AND SERVICE BLADE ASSEMBLY CAUTION: DO NOT HANDLE MOWER BLADES WITH BARE HANDS. CARELESS OR IMPROPER HANDLING MAY RESULT IN SERIOUS INJURY. BLADE CARE For best results mower blades must be kept sharp. The blades can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen blades while they are still on the mower. BLADE SERVICE (Refer to fig. 9) TO REMOVE BLADE ASSEMBLY FROM DECK • Remove cotter pin from the spindle shaft. • Remove nut and washer from the spindle shaft. • Pull blade assembly off the spindle shaft. (Watch for a key in the spindle shaft.) TO REMOVE BLADES FROM BLADE ASSEMBLY. • Remove cotter pin from the blade bolt. • Remove nut from the blade bolt. • Remove blade from the blade assembly. BLADE SHARPENING • Blades can be sharpened with a file or grinding wheel. NOTE: When sharpening blades take care to maintain blade balance. Sharpen both blades equally even if one blade does not need to be sharpened. Check balance by weighing each blade to make sure they are equal in weight. FIG. 9 WARNING: SHUT OFF MOWER ENGINE AND REMOVE SPARK PLUG WIRE FROM SPARK PLUG BEFORE MAKING ANY ADJUSTMENTS OR REPAIRS TO THE MOWER. CLEANING THE MOWER Water pressure from a garden hose will remove fresh clippings from the underside of the mower. Clean mower after each mowing. DAILY MAINTENANCE Make sure all nuts and bolts are tight, cotter pins and retainer springs are secure. Keep blades sharp. Observe all Safety Precautions. Keep mower well lubricated. REPAIR PARTS Your rotary mower has been produced with components designed for your unit. Although standard V-belts, bearings, blades, pulleys, etc. may look like parts used on your rotary mower, while similar in appearance many are of a different construction and could in some cases cause a malfunction in the operation of the machine. For continued satisfactory performance use only repair parts supplied by the manufacturer. See the dealer where the mower was purchased for factory replacement parts. CAUTION: IF YOUR BLADE BOLTS SHOW WEAR, REPLACE THEM WITH FACTORY REPLACEMENTS ONLY. TO REINSTALL BLADES • Assemble a blade bolt through a flat washer, a blade and then another flat washer. • Assemble the bolt through the hole in the stump plate and the blade hub assembly. • Assemble a flat washer and nut onto the blade bolt. • Tighten nut, then loosen just until blade can pivot. • Install a cotter pin to secure the nut. TO REINSTALL BLADE ASSEMBLY TO MOWER • Reinstall key in spindle shaft, if necessary. • Install the blade assembly onto the spindle shaft. • Secure with flat washer and nut. • Torque the spindle shaft and nut to 100 FT. LBS. and secure with a hair cotter pin. CUSTOMER RESPONSIBILITIES CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in “DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the “DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the “DISENGAGED" position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above procedure until you have the correct tension. INNER NUTOUTER NUTSWITCHBODYCLUTCH LEVER1/8" ENGINEPULLEYBLADEPULLEYIDLERPULLEYCLUTCH LEVERPLUNGERREAR DRIVECOVERFOURSCREWS CUSTOMER RESPONSIBILITIES INSTALLING NEW V-BELT • Feed new V-belt between the two belt guides at the Engine Pulley. • Place V-belt up and around the Engine Pulley. Check to make sure the V-belt is seated properly in the groove of the Engine Pulley. • Place V-belt along inside of Idler Pulley. • Wrap V-belt down around Blade Pulley, placing Belt inside of Rear Belt Guides. • Reinstall V-belt Keeper Rod and secure with Small Hair Pin....

Questo manuale è adatto anche per i modelli :
falciatrici - 45-03621 (3.65 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie