valutazioni - 4, GPA: 4.8 ( )

Produttore : Agri-Fab File Size : 2.99 mb File Nome : Lingua di insegnamento:

PULLEY CLUTCH LEVER PLUNGER REAR DRIVE.. COVER FOUR.. SCREWS CLUTCH CABLE ADJUSTMENT • Remove four screws from Rear Drive Cover. Lay aside cover and screws. • Place Clutch Lever in "DISENGAGED" position • The Cable should be under slight tension but should not pull the Clutch Lever more than 1/8" away from the Switch Body. NOTE: If the Plunger extends more than 1/8" out from the switch body, the cable tension is too tight and the Engine will not start. TO INCREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the inner nut on the Clutch Cable. • Tighten the outer nut on the Clutch Cable. TO DECREASE CABLE TENSION • Place Blade Clutch Lever in the "DISENGAGED" position. • Loosen the outer nut on the Clutch Cable. • Tighten the inner nut on the Clutch Cable. • Repeat the above procedure until you have the correct tension. • • • NO the Eng TO • • • TO • • • • 19 CUSTOMER RESPONSIBILITIES V-BELT REPLACEMENT • V-belt must be replaced if it becomes stretched to the point that it can no longer be adjusted, or if it becomes frayed or otherwise can not function properly. • Move Blade Clutch Lever to the "DISENGAGED" position. CAUTION: DISCONNECT SPARK PLUG WIRE REMOVING OLD V-BELT • Remove Rear Drive Cover. • Remove Front Drive Cover. • Remove Hair Pin and Clevis Pin from Clutch Cable. • Loosen two Rear Belt Guides and pivot them away from Blade Pulley. • Remove V-belt from around Blade Pulley. • Remove one small Hair Pin from Belt Keeper Rod and slide Belt Keeper Rod to the side. • Pull V-belt down from around Engine Pulley and remove V-belt from Mower. BELT GUIDES INSTALLING NEW V-BELT • Feed new V-belt between the two belt guides at the Engine Pulley. • Place V-belt up and around the Engine Pulley. Check to make sure the V-belt is seated properly in the groove of the Engine Pulley. • Place V-belt along inside of Idler Pulley. • Wrap V-belt down around Blade Pulley, placing Belt inside of Rear Belt Guides. • Reinstall V-belt Keeper Rod and secure with Small Hair Pin. Check to make sure V-belt is over top of Keeper Rod. • Reposition and retighten two Rear Belt Guides at the rear of the Blade Pulley. Leave approximately 1/16" between Guides and Pulley. • Reinstall Clevis Pin and Hair Pin into Clutch Cable. • Reinstall Front Drive Cover and Rear Drive Cover. ENGINE PULLEY BELT KEEPER ROD V-BELT REAR BELT GUIDES BLADE PULLEY HAIRPIN AND CLEVIS PIN 20 STORAGE 21 22 42" ROUGH CUT TRAILMOWER - MODELS 45-03072 & 45-03611 42" ROUGH CUT TRAILMOWER - MODELS 45-03072 & 45-03611 ITEM PART NO. DESCRIPTION 1. HA24255 MOWER DECK 2. HA24378 GUARD WHEEL 3. HA23193 SCREW 3/8-16 X 1-1/4 THD. FORMING 4. HA24292 BRACKET BELT GUIDE 5. HA24293 ROD BELT GUIDE 6. HA3090 PIN HAIR COTTER 7. HA24294 V-BELT (B SEC. 60" O.C.) 8. HA24295 CHANNEL CLUTCH LEVER 9. 45100 BOLT 1/2-13 X 4" HEX HEAD 10. HA120396 WASHER 1/2 FLAT 11. 43262 NUT 1/2-13 HEX LOCK 12. HA14232 WASHER FLAT 13. HA24296 ROD CLUTCH LINK 14. 44101 PIN, COTTER 3/32" X 3/4" 15. 43081 WASHER FLAT 5/16" STD. WRT. 16. HA24297 SPRING CLUTCH 17. HA24617 CLUTCH CABLE ASSY (Model 45-03071) 49165 CLUTCH CABLE ASSY (Model 45-0361) 18. 25292 STRAP, CLUTCH ADJUSTING 19. 43661 BOLT, 1/4-20 X 1" HEX HEAD 20. 43016 NUT 1/4-20 HEX LOCK 21. 25262 BRACKET INTERLOCK MOUNTING 22. HA23199 SWITCH INTERLOCK 23. 64904 MODULE ASSY WITH WIRES 24. 712-0121 NUT #10-24 HEX 25. 47078 SCREW #10-24 X 3/4" 26. 48840 SCREW 1/4-20 WASHER HEAD 27. 48298 CLIP, CORD 28. HA24300 WHEEL MOUNTING BRACKET L.H. 29. HA24301 WHEEL MOUNTING BRACKET R.H. 30. HA4143 WASHER FLAT 31. HA137258 PIN COTTER 3/16" X 1-3/4" 32. HA24308 TIRE 33. HA23229 CAP HUB 34. HA24309 STRAP ADJUSTING 35. HA6979 WASHER FLAT 36. 43020 BOLT 1/2-13 X 1-1/2 HEX HEAD 37. 43019 NUT 1/2-13 HEX JAM 38. HA23220 PIN LOCATING 39. 47134 PIN HAIR COTTER .08" X 1.58" 40. HA24311 CHAIN DEFLECTOR ITEM PART NO. DESCRIPTION 41. HA24312 ROD CHAIN 42. HA24313 BRACKET CHANNEL 43. HA9131 SCREW SELF THREADING 44. 25428 PLATE ENGINE MOUNTING 45. 49161* ENGINE, 11 HP 46. HA24457 PULLEY 47. HA3073 KEY 1/4" SQ. X 1" 48. HA115321 SCREW 5/16-18 X 5/16 SOC. SET 50. 43555 WASHER 7/16" LOCK 51. HA181668 BOLT 7/16-20 X 1-1/4 HEX HEAD 52. 25051 COVER, GAS TANK 53. 25265 COVER, FRONT DRIVE 55. 43182 BOLT 5/16-18 X 3/4 HEX HEAD 56. 43064 NUT 5/1...

Scarica la tua

Per scaricare, digitare 2 cifre :