Log:
valutazioni - 5, GPA: 4 ( )

Istruzioni per l'uso Cisco Systems, Modello CATALYST MEM-C6K-FLC16M

Produttore : Cisco Systems
File Size : 180.54 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Note The 16-MB MEM-C6K-FLC16M and 24-MB MEM-C6K-FLC24M linear Flash PC cards are formatted for the Catalyst 6500 series supervisor engines and are ready to use. The MEM-C6K-ATA-1-64M and 64-MB MEM-C6K-FLC64M Flash PC cards are not formatted. You must format these cards (see Table 1 on page 7 for a description of the format command.) When you enter the dir disk0: or dir slot0: commands, an unformatted Flash PC card returns a “bad device block info” or “invalid magic number” error message. Note Supervisor Engine 1 and Supervisor Engine 2 do not support the same Flash PC card format. To use a Flash PC card with Supervisor Engine 2, you must format the card with Supervisor Engine 2. To use a Flash PC card with Supervisor Engine 1, you must format the card with Supervisor Engine 1. Table 1 Table 1Table 1Table 1shows many of the commands that are available for using and managing Flash devices, including the Flash PC cards. To perform specific tasks, use these commands either alone or combined with other commands. For example, to copy a file from a TFTP server to a Flash PC card, set the BOOT environment variable so that the system will boot from this new image and then verify the boot sequence as shown in the following steps: Note The following commands listed in Table 1 are not applicable to the ATA Flash (disk0:) PC card: undelete, squeeze, show flash devices, show flash, and verify. Note The ATA Flash PC card is accessed through disk0: and the 16-MB, 24-MB, and 64-MB Flash PC cards are accessed through slot0:. The following procedure uses slot0:. Step 1 Copy a file from a TFTP server to the Flash PC card in slot0: Console (enable) copy tftp slot0: Step 2 Set the BOOT environment variable so that the system boots from slot0: Console (enable) set boot system flash slot0:cat6000-sup-5-1-1-CSX.bin prepend Step 3 Display the contents of the BOOT environment variable: Console (enable) show boot For complete descriptions of these commands and how to use them, refer to the Catalyst 6500 Series Software Configuration Guide and the Catalyst 6500 Series Command Reference publication. 6 Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note 78-6507-06 Using Flash PC Cards Table1 Commands for Using and Managing Flash Devices Task Command Copy a Flash file to a TFTP server, another Flash device, or to the running configuration. copy m/device:filename {tftp | flash | m/device:filename | config} Copy a file from a TFTP server to a Flash device or to the running configuration. copy tftp {flash | m/device:filename | config} Copy a file from Flash memory to a TFTP server or to a Flash device, or to the running configuration. copy flash {tftp | m/device:filename | config} Copy the running configuration to another Flash device or to a TFTP server. copy config {flash | m/device:filename | tftp} Set the BOOT environment variable. set boot system flash device:[filename] [prepend] [mod_num] Format a Flash PC device. format [spare spare-number] [m/]device1: [[device2:] [monlib-filename]] Specify the boot field in the configuration register, which determines the boot method the switch will use at the next set boot config-register boot {rommon | bootflash | system} [mod_num] startup. Display the contents of the BOOT environment variable. show boot [mod_num] Clear a specific image from the BOOT environment variable. clear boot system flash device:[filename] [mod_num] Clear the entire BOOT environment variable. clear boot system all [mod_num] Display a list of files on a Flash device. dir [[m/]device:][filename] [all | deleted | long] Set the default Flash device for the system. cd [[m/][bootflash: | slot0:]] Verify the default Flash device for the system. pwd [mod_num] Delete a file on a Flash device. delete [[m/]device:]filename Undelete a file on a Flash device. undelete index [[m/]device:] Permanently remove all deleted files on a Flash device. squeeze [m/]device: Identify the supported Flash devices on the system. show flash devices Display information about the Flash PC. show flash [[m/]device:] [all | chips | filesys] Verify the checksum of a file on a Flash device. verify [[m/]device:] filename Catalyst 6500 Series Supervisor Engine Flash PC Card Installation Note 7 Additional Documentation Additional Documentation Refer to the following documents for additional information on supervisor engine Flash devices: • Release Notes for Catalyst 6500 Series and Cisco 7600 Series Internet Router Supervisor Engine 2 ROMMON • Catalyst 6500 Series Software Configuration Guide • Catalyst 6500 Series Command Reference Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation at this URL: You can access the Cisco website at thi...

Questo manuale è adatto anche per i modelli :
falciatrici - CATALYST MEM-C6K-ATA-1-64M( (180.54 kb)
falciatrici - CATALYST MEM-C6K-FLC24M (180.54 kb)
falciatrici - CATALYST MEM-C6K-FLC64M (180.54 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie