valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
(Figure ASM-R-0151) ASSEMBLY © 2006 Alamo Group Inc. ASSEMBLY A96B 03/06 Assembly Section 3-13 CHAIN GUARD (EXTRA EQUIPMENT) CHAIN GUARDS: Front and Rear Chain Guards (Optional Equipment) are recommended for higher than normal usage (100 hours or more per year) and will provide protection from thrown objects with careful operation. Chain Guards must be maintained in good repair by replacing missing or worn sections or by being replaced when seriously worn or damaged. Front Chain Guards 1. Attach the right and left Chain Guard (1) to the mower with 1/2” x 1-1/4” Bolts (2), Flatwashers (3), and Locknuts (4). Fasten chain links (5) to guard by inserting rod (6) through each link and bending over the ends. (Figure ASM-R-0152) Rear Chain Guards 1. Attach the Right Chain Guard Mounting Plate (1) & the Left Chain Guard Mounting Plate (2) to the mower with 1/2” x 1-1/2” Bolts (3), Flatwashers (4) and Locknuts (5). Then attach Chain Guards (6) to Chain Guard Mounting Plates with 1/2” x 1-1/2” bolts(7) Flatwashers(8) and Locknuts (9). For Double Chain Guards attach with 1/2” x 3" bolts (10), Flatwashers (11), Spacers (12) and Locknuts (13). Fasten Side Rear Chain Guard (14) to Chain Guard Mounting Plates (1&2) with 1/2” x 1-1/4” bolts (15) Flatwashers (16) and Locknuts (17).(Figure Asm-R-0153) ASSEMBLY © 2006 Alamo Group Inc. ASSEMBLY A96B 03/06 Assembly Section 3-14 JACKSHAFT BEARING SUPPORT ASSEMBLY Insert the splined end of jackshaft into the Bearing Support, (Figure ASM-R-0154), and attach the Jackshaft Bearing Support to the Tongue Lugs as shown. Insert bushing (item 1) into Bearing Supports, install 5/8 x 8 capscrew (item 2) with flatwasher (item 3) against bushing, and install locknut (item 4) and tighten securely. NOTE: Install bearing assembly with flush side toward tractor. Bearing should be rigidly attached to jackshaft when shipped. If not, apply Locktite 609 between shaft and bearing to lock in place. CV JACKSHAFT SUPPORT ASSEMBLY Insert the splined end of Jackshaft into the Bearing (6) and attach the Jackshaft Mount (1) to the Tongue with 5/ 8” x 2" bolt (2), flatwasher (3), and locknut (4) as shown in Figure ASM-R-0155. Attach Jackshaft Support (7) to Mount (1) using 5/8” x 1-1/2” bolts (5) and locknut (4). Clamp top and middle section of Support by using 1/ 2” x 7" bolts (10) and locknuts (8), placing Spacers (9) between Supports. NOTE: Install bearing assembly with snap ring facing jackshaft. Bearing should be rigidly attached to jackshaft when shipped. If not, apply Locktite 609 between shaft and bearing to lock in place. ASSEMBLY © 2006 Alamo Group Inc. OPERATION SECTION Operation Section 4-1 © 2006 Alamo Group Inc. OPERATION A96B 03/06 Operation Section 4-2 ALAMO A96B MEDIUM-DUTY ROTARY MOWER OPERATION INSTRUCTIONS Alamo A96B rotary mowers are manufactured with quality material by skilled workers. These mowers are designed to cut grass, weeds, small brush and other vegetative material up to 2” diameter in areas such as pastures, industrial areas, and roadsides. The mower is equipped with protective deflectors and/or chain guards to prevent objects being thrown from the mower by the blades, however, no shielding is 100% effective. All shields, guards, deflectors, and chains equipped on the unit must be maintained on the mower in good operational condition. It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the mower, tractor, or a thrown object. Do not operate the mower if passersby, pets, livestock, or property are directly in front or to the rear of the unit. This section of the Operator’s Manual is designed to familiarize, instruct, and educate safe and proper mower use to the operator. Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a rotary mower and are not of a A96B cutter. Some pictures may show shields removed for purposes of clarity. NEVER OPERATE this implement without all shields in place and in good operational condition. The operator must be familiar with the mower and tractor operation and all associated safety practices before operating the mower and tractor. Proper operation of the mower, as detailed in this manual, will help ensure years of safe and satisfactory use of the mower. IMPORTANT: To avoid mower damage, retorque all bolts after the first 10 hours of operation. Retighten blade carrier retaining nut on gearbox lower shaft to 300 ft. lbs. READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND MOWER. If you do not understand any of the instructions, contact your nearest authorized dealer for a full explanation. Pay close attention to all safety signs and safety messages contained in this manual and those affixed to the cutter and tractor. OPS-U- 0001 READ, ...
Questo manuale è adatto anche per i modelli :falciatrici - A96B (41.14 mb)
falciatrici - FC-0015 (41.14 mb)
falciatrici - FC-0016 (41.14 mb)