valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
iMPORTANT: Be sure to re-attach muffler and heat shield after bumper is installed. • If rear mounting holes in tractor frame are empty, install hex bolts and whizlock nuts supplied in the parts bags. See figure 5. STEP 5: (SEE FIGURE 6) • Spread ends of bumper enough to fit slots onto bolts in rear mounting holes in tractor frame. • The bumper has three mounting holes. The rear hole provides the most clearance while the forward holes provide a neater appearance. Use a hole that provides enough clearance for hood to stay in raised position when opened. Attach the bumper using either standard hex bolts and whizlock nuts or self threading bolts and lock washers. Use the self threading bolts if standard hex bolts do not insert freely into the hole in the tractor frame. iMPORTANT: Before fully tightening bolts, be sure tractor hood will stay in raised position when opened. Call 1-888-578-8388 for missing parts or assembly help DO NOT RETURN TO STORE (LT) LAWN TRACTOR REMOVE BOLT iNSTALL (C), (D) IF iF PRESENT HOLE iS EMPTY SUSPENSION BRACKET (LT) LAWN TRACTOR REMOVE BOLT iNSTALL(C), (D) iF iF PRESENT HOLE iS EMPTY / SUSPENSION BRACKET (GT) GARDEN TRACTOR EXHAUST TUBES MUFFLER BROWNING SUSPENSSHIEION LD BRACKET J \/ REMOVE IF PRESEBOLT NT FIGURE 5 LAWN TRACTOR (LT) SHOWN WHIZLOCK NUT (D) FOR BOLT (B) (E) FORBOLT(A) BOLT(A) or (B) FIGURE 6 7 7 ( iDENTiFY YOUR TRACTOR FRAME ) For all tractors with model numbers beginning with 247, look at the side of your tractor directly underneath the hood (Figure 1A & 1B). If your frame resembles the one shown in 1A, go toTRACTORS WITH FRAME SHOWN IN FIGURE 1A on page 8. If your frame resembles the one shown in 1B, go to TRACTORS WITH FRAME SHOWN IN FIGURE 1B on page 10. FIGURE 1A FIGURE 1B NOTE: Only the front of the tractor frame is shown for clarity. TRACTORS WiTH FRAME SHOWN iN FIGURE 1A STEP 1: (SEE FIGURE 2) HARDWARE SHOWN FULL SIZE * Open parts bag labelled "A" and verify that all parts EXCEPT WHERE NOTED are present. NOTE: Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. Ref. Part Qty. Description (not full size) A 43350 4 Carriage Bolt, 3/8-16 x 1" B 44072 4 Whizlock Nut, 3/8" C R19171616 4 Washer, 1/2"x 1" D 44742 2 Plug (486.24611 Bumper) 47674 4 Plug (486.24612 Bumper) E 48106 2 Shoulder Bolt, 3/8-16 x .9" F 47856 2 Lag Screw, 5/16 x 3/4" G 43001 2 Hex Bolt, 3/8-16 x 1" H 46584 2 Whizlock Nut, 5/16" I 43182 2 Hex Blot, 5/16 x 3/4" _-_H PARTS BAG "A" FIGURE 2 8 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE STEP 2: (SEE FIGURE 3) * Place plug on a work bench or solid table and push end of bumper down onto plug. Repeat for all plugs. BUMPER PUSH DOWN WiTH EVEN PRESSURE WORK BENCH OR SOLID TABLE I STEP 3: (SEE FIGURE 4) * Assemble a 0.9 x 3/8" shoulder bolt and 3/8" whizlock nut to each side of the tractor frame. Tighten. SHOULDER BOLT 3/8" WHIZLOCK NUT _. 1 I FIGURE 4 STEP 4: (SEE FIGURE 5) • Slide the lower slots of the bumper onto the shoulder bolts you assembled to the tractor frame in step 1. e o e e e STEP 5: (SEE FIGURE 6) e Assemble a 5/16 x 3/4" lag screw to the bumper and tractor frame. Repeat for other side. FIGURE 6 Call 1-866-576-8388 for missing parts or assembly help 9 DO NOT RETURN TO STORE TRACTORS WITH FRAME SHOWN iN FIGURE 1B STEP 1: (SEE FIGURE 2) * Open parts bag labelled "A" and verify that all parts are present. NOTE: Place cardboard or a mat on work surface to prevent scratching of parts removed from carton and tractor. Ref. Part Qty. Description A 43350 4 Carriage Bolt, 3/8-16 x 1" B 44072 4 Whizlock Nut, 3/8" C R19171616 4 Washer, 1/2"x 1" D 44742 2 Plug (486.24611 Bumper) 47674 4 Plug (486.24612 Bumper) E 48106 2 Shoulder Bolt, 3/8-16 x .9" F 47856 2 Lag Screw, 5/16 x 3/4" G 43001 2 Hex Bolt, 3/8-16 x 1" H 46584 2 Whizlock Nut, 5/16" I 43182 2 Hex Blot, 5/16 x 3/4" STEP 2: (SEE FIGURE 3) • Place plug on a work bench or solid table and push end of bumper down onto plug. Repeat for all plugs. HARDWARE SHOWN FULL SiZE EXCEPT WHERE NOTED ..... B (not full size) G ........ H PARTS BAG "A" FIGURE 2 BUMPER PUSH DOWN WiTH EVEN PRESSURE WORK BENCH SHORT STEP OR SOLID TABLE PLUG FIGURE3 1 0 Call 1-866-576-8388 for missing parts or assembly help DO NOT RETURN TO STORE STEP 3: (SEE FIGURE 4) * Assemble a 3/8 . 1" hex bolt and 3/8" whizlock nut to tractor frame and middle slot of the bumper. * Tighten and then loosen nut one half turn. * Repeat for other side of bumper. f 3/8" WHIZLOCK NUT FIGURE 4 STEP 4: (SEE FIGURE 5) * Assemble a 5/16 x 3/4" he.bolt and 5/16" whizlock nut to the tractor frame and bumper. Tighten. * Repeat for other side of bumper * Tighten the two 3/8" whizlock nuts assembled in step 1. 5/16" WHIZLOCK NUT FIGURE 5 Call 1-888-578-8388 for missing parts or assembly help DO NOT RETURN TO STORE Your Home For expert troubleshooting and home solutions advice: For repair -in your home -of all major brand appliances, lawn and garden equi...
Questo manuale è adatto anche per i modelli :falciatrici - 486.24612 (1.02 mb)