valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
D t / J ........ E ...... F Ref. Part No. Qty. Description Ref. PaA No. Qty, Description A 48894 2 Self Threading Screw, 3/8-16 x 1-1/2 F 1643-60 2 Plastic Grip B 43062 2 Hex Bolt, 3/8-16 x 1-1/2" G HA21362 4 Nylock Nut, 3/8" C 43001 2 Hex Bolt, 3/8-16 x 1" H 43003 4 Lock Washer, 3/8" D 44742 4 Plug ] 43070 4 Washer, 3/8" E 48866 2 Pivot Spacer 2 CARTON CONTENTS Ref, Description Part No. 1 2 3 4 Right Mounting Bracket Left Mounting Bracket Locking Lever Bumper #25038 #25037 #64862 #64614B #64614S #64614C (71-246212) (71-246221) (71-246231) TOOLS REQUIRED (2) 9/16" Wrenches (1) 1/2" Wrench (for heat shield on page 5) ASSEMBLING TO SINGLE ROD DECK SUSPENSmON TRACTORS IMPORTANT: If your tractor has a single mower deck suspension bracket located under the middle of the front axle as shown in figure 1, continue with the instructions on this page, if your tractor does not have a mower deck suspension bracket like the one shown, go to page 5, II _J BRACKET FIGURE 1 VIEWED FROM FRONT CAUTION! Muffler is hot! Allow engine to cool down before proceeding with bumper installation, NOTE: Right hand (RH) and left hand (LH) are determined from the operator's position while seated on the tractor, STEP 1: (SEE FIGURE 2) , Place cardboard on work surface. identify and lay out all parts and hardware. Not all hardware wil! be used. Unused hardware may be discarded after assembly. Remove hood from tractor using instructions in your tractor owner's manual. Place hood on cardboard or on a mat to protect paint. , Remove the browning shield from the front of the tractor as shown. IMPORTANT: Be sure to reattach the browning shield after bumper is installed, REMOVE FRONT SCREWS REMOVE BROWNmNGSHmELD FIGURE 2 STEP 2: (SEE FIGURE 3} Place plug (D) on a work bench or solid table and push end of bumper down onto plug. Repeat for all four plugs. BUMPER PUSH DOWN WiTH EVEN PRESSURE WORK BENCH OR SCUD TABLE FIGURE 3 3 STEP 3: (SEE FIGURE 4) , Attach left mounting bracket to hole shown in left side of tractor frame using a hex bolt (C), fiat washer (I) and nylock nut (G). Align middle hote in bracket with empty hole in tractor frame. Tighten nylock nut (G) only enough to keep bracket in alignment until step 4. Repeat for right mounting bracket. (GT) FRAME SHOWN HEX LEFT MOUNTING BUMPER STOPS BOLT (C) BRACKET FACE OUT _ NYLOCK NUT (G) FLAT WASHER (0 / AUGN THESE HOLES FIGURE 4 LEFT SIDE VIEW STEP 4: (SEE FIGURE 5) , Fasten bumper to mounting bracket using a hex bolt (B), pivot spacer (E), a locking lever, a fiat washer (I) and a ny!ock nut (G) as shown, The pivot spacer inserts into hole in bumper. Tighten both nuts on mounting bracket at this time. Repeat for other side. , Assemble plastic grips (F) onto locking levers. , Lift up on bumper until pins in locking levers snap into holes in mounting brackets. IMPORTANT: You must lower bumper before raising tractor hood. Pu!! out on locking levers and push bumper down as far as it will go. PIVOT SPACER (E)_ FLAT WASHER (I) GRUP(F) FIGURE 5 LEFT SIDE VIEW STEP 5: (SEE FIGURE 6) , Replace the front screws and browning shield you removed in Step 1 as shown. FRONT SCREWS REPLACE BROW...
Questo manuale è adatto anche per i modelli :falciatrici - 486.246212 (643.84 kb)
falciatrici - 486.246231 (643.84 kb)