valutazioni - 4, GPA: 4.5 ( )

Produttore : Poulan File Size : 727.42 kb File Nome : Lingua di insegnamento:

5 END CAP COVER ASSEMBLY SUPPORT POST MOUNTING BRACKET LANCED TABS BRACKET SUPPORT PIN RETAINER SPRING MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "D" NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting assembly to tractor. 1. Raise seat on tractor to allow assembly to be mounted. 2. With cover closed, lift assembly and place support post inside mounting bracket. Allow assembly to rest on lanced tabs of mounting bracket. 3. Line up holes in mounting bracket with holes in support post and insert bracket support pin. Secure with retainer spring. 4. Unlatch and open cover. 5. Install the three (3) tubing end caps onto container support. 6. Tap each end cap onto container support tubes to seat securely. 5 6 CONTAINER ASSEMBLY (See Fig. 6) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonly arecomme ndedreplacementcontainer. 02097 FIG. 6 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 9 LATCH WELD NUT WASHER LOCK WASHER LATCH WELD NUT LOCK WASHER WASHER SCREW FIG. 8A DEFLECTOR SHIELD FIG. 8B LATCH HOOKS 8 CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. LOWER CHUTE (See Figs. 8A & 8B) Use Hardware - - GROUP "E" 1. Press weld nut into rubber latch and install two latch hook assemblies to lower chute using screw, washer, and lock washer as shown. 2. Tighten hardware securely. 3. Raise and hold defl ector shield in upright position. 4. Place front of chute over front of mower deck opening and slide into place, as shown. 5. Hook front latch into latch bolt on front of mower deck. 6. Hook rear latch into latch bolt on back of mower deck. WARNING Donotoperatemowerunlesscontainerisproperlyis subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING 02082 CONTAINER MOUNTING (See Fig. 7) No hardware required 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center support tube. 7 COVER LATCH HANDLE CENTER SUPPORT TUBE CONTAINER WARNING CONTAINER HANDLE FIG. 7 CONTAINER WARNING 02102 FIG. 9 UPPER CHUTE LOCK WASHER WELD NUT ACORN NUT SPLIT SPACER WASHERS 3/16 X 3/4 X 16 #10 X 1-1/8" SCREW GA. WASHER 3/16 X 3/4 X 16 GA. LOWER CHUTE #10 X 5/8" SCREW RUBBER LATCH CHUTE LATCH ASSEMBLY (See Fig. 9) Use Hardware - - GROUPS "F & G" 1. Assemble latch pin to upper chute, as shown. 2. Press weld nut into rubber latch and assemble rubber latch to lower chute, as shown. 3. Tighten all hardware securely. 9 10 02098 02099 WHEEL WEIGHTS (See Fig. 11) Use Hardware - - GROUP "H" 1. Assemble wheel weights and U-bolts onto the outside of front wheels and hold in position. 2. Fasten locknuts onto U-bolts on the inside of wheel and tighten securely. 11 FIG. 11 WHEEL WEIGHT FRONT WHEEL LOCKNUTS U-BOLT FULL BAGGER INDICATOR LOWER CHUTE COVER UPPER CHUTE ALIGNMENT SLOTS LATCH PIN BOSSES FIG. 10B FIG. 10A HANDLE RUBBER LATCH 10 UPPER CHUTE (See Figs. 10A & 10B) No hardware required 1. Lower mower deck to its lowest cutting position. 2. Assemble upper chute by inserting curved end into hole in back of cover. NOTE: Handle carefully so as not to damage full bag in di - ca tor. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. 12 LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for man ce. See your tractors owner's manual for ins truc tions. OPERATION TIPS FOR IMPROVED BAGGING OPE RATION: Follow the mower operation instructions in your tractor owner's manual. When operating your grass catcher on a lawn where grass and leaf bagging equipment has not been used, you are picking up thatch and debris that has accumulated for long periods of time. The amount collected and the total time of operation may be greater than you will experience with regular use of your grass catcher. • Alway...

Scarica la tua

Per scaricare, digitare 2 cifre :