valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
If possible, always cut the grass when it is relatively dry. To obtain a clear pattern, push the appliance in straight lines at an even walking pace. The cutting paths should overlap by a few centimetres to avoid leaving strips of grass. Maintenance, care and storage Maintenance covers all work required to keep the mower in good operating condition. Regular checks (firm fit of screw connections, cracks, damage) and replacement of damaged or worn parts will help prevent accidents and mower failures. • Clean the mower after use and lightly grease the bearings. Grease the cutting blades. • Store the mower in a dry room. • Models with contactless cutting technology cannot be re-sharpened due to the special cutting geometry. The cutting equipment (consisting of the lower blade and blade roller) must, if necessary, be replaced as a complete set. Ask your retailer, he will be pleased to advise you. Repairs on the mower and the installation of blades may only be implemented by appropriate specialist workshops. • Have your mower checked in the autumn where possible so that it is ready to use in the next mowing season. - • For safety reasons, only use orig nal spare parts supplied by the manufacturer or parts that have -J been authorised by the manufacturer. • We expressly point out that in accordance win product liability laws, we are not liable for any damage caused by our units if this damage is; due to improper repair or if parts exchanged are not our original parts or parts approved b. us, and if the repairs were not carried out at service centre authorised by the manufacture' or by an authorised specialist. The same applies to spare parts and accessories. Adjusting the cutting equipment Pictures © and © The cutting equipment on your mower was correctly set before leaving our factory. If the lawn cut becomes untidy after longer use, correct the lower blade position. Attention! Rotating cutting equipment. Danger of cutting from sharp blades. • Working on the cutting equipmen: can lead to serious injury from cuts. Always wear protective gloves when implementing changes in settings or maintenance work on the cutting equipment. The cutting equipment cor tinues to rotate after you stop mowing! 18 • Turn the mower upside down through 180° so that the blade roller points upwards. • Insert the supplied thickness gauge between the blade of the blade roller and the lower blade on the left-hand side. • Turn the hexagonal screw with a 10 mm open-end wrench clockwise until the thickness gauge is lightly in contact. Repeat this procedure on the right-hand side of tfe mower. Checking the cutting equipment with a cutting test Picture (£) Attention! Rotating cutting equipment. Danger of cutting from sharp blades. • Working on the cutting equipment can lead to serious injury from cuts. Always wear protective gloves when implementing changes in settings or maintenance work on the cutting equipment. The cutting equipment continues to rotate after you stop mowing! • Rotate the blade roller to test it; none of the 5 blades should touch or rub on the lower blade. • Carry out a cutting test as shown with newspaper. To rotate the blade roller turn the roller. Never put your hand into the cutting equipment Tips_ Mowing with the grass catcher (accessories) Picture O You do not have to rake up the grass clippings if you use the grass catcher. This is available as an accessory from specialist retailers. To ensure clippings are correctly collected, ensure that the lawn is dry and that you push the mower at a relatively fast speed. Environmental protection The packing material and the unit and accessories are made of materials that can be recycled. Appropriate separation and disposal of the remaining materials helps recycling. Troubleshooting_ General Faults usually occur if the appliance has not been handled, cared for or mar tar ec properly. The following table “Eliminator c* ra_ ts* contains the most common faults a a remed es to eliminate these faults. If you nave ary other problems, please contact your nearest service centre authorised by the manufacturer, or your nearest authorised spec a s: deafer. 19 Elimination of faults Fault Possible Cause Remedy Abnormal noises, lawnmower rattles Screws on the cutting equipment or mower housing are loose Tighten bolts Lawn turning yellow, cut not clean Blade is too blunt Cutting height too low Change blade Use a slightly higher cutting heigh Cutting gap between blade roller and lower blade is too large Readjust cutting gap with thickness gauge The appliance leaves deep tracks Ground softened by water, lawn too wet Allow lawn to dry. do not mow if grass is wet Disposal of appliance This symbol on the product, operating instructions or packaging indicates that this product, at the end of its service life, may not be disposed of as normal household waste. It must be disposed of at a collection point for the recycling of electric and electronic applia...
Questo manuale è adatto anche per i modelli :falciatrici - Razorcut Premium 38 (857.24 kb)