valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
Tighten the nuts. See figure 6. • Assemble the grip onto the end of the lift handle. See figure 6. FIGURE 3 • Tighten the bolts and nuts assembled in figure 3. Tighten the bolts and nuts assembled in figure 1. Tighten the rear bolts and nuts assembled in figure 2. • Assemble the axle bracket to the outside of the rear angle brackets using two 5/16" x 1" hex bolts and 5/16" nylock nuts. The angled ends of the axle bracket must point as shown in figure 4. Tighten the bolts and nuts and then loosen slightly. LIFT HANDLE GRIP 5/16" NYLOCK NUT 5/16" x 1" HEX BOLT5/16" NYLOCK NUT 5/16" x 1" CARRIAGE BOLT 5/16" NYLOCK NUT 5/16" x 1" HEX BOLTAXLE BRACKET FIGURE 4 FIGURE 6 OPERATION Regular removal of thatch is critical to maintenance of a healthy lawn. Excessive thatch prevents air, water and fertilizer from reaching the roots. To effectively dislodge excessive thatch from your lawn, read these instructions for proper adjustment and operation of the dethatcher. OPERATING TIPS • Vary the vehicle's forward speed until the best dethatching action is achieved. • For best results, use a crisscross pattern on your lawn. • If the dethatcher appears to be "jumping" during use, then extra weight should be added to the tine shield. In most conditions extra weight will be needed. Concrete patio blocks are recommended for weight because of their low profile; however any type of weight is suitable if it can be tied down to the shield. Secure weight by using suitable binding material such as rubber tie down straps or wire, fastening to the holes in the shield flange. See figure 8. ADJUSTMENT OF TINE SHIELD • Move the towing vehicle onto a level surface, such as a driveway or garage floor and attach the tine dethatcher to the vehicle hitch. See figure 7. • Lower the dethatcher into operating position using the lift handle. Loosen the two nylock nuts and carriage bolts which fasten the hitch mount arms to the hitch arm mount brackets at the rear of the tine shield. Adjust the tine shield until it is level and both the front and rear spring tines are in contact with the ground. Retighten the hex nuts. See figure 7. HITCHMOUNTARMS CARRIAGE BOLT& NYLOCK NUT FIGURE 8 FIGURE 7 MAINTENANCE/STORAGE CUSTOMER RESPONSIBILITIES • Read and follow the maintenance schedule and the maintenance procedures listed in this section. Every season Before storage Before each use After each use MAINTENANCE SCHEDULE Fill in dates as you complete regular service. Service Dates Check for loose fasteners X Lubrication X • Before each use check all nuts and bolts for tightness. • Lubricate wheels at least once a year or as needed. • If rust appears on the shield or spring tines, sand lightly and coat with enamel paint. • Always store in a dry area, and coat exposed metal with light oil when not in use. • To remove a spring tine, insert a screw driver or punch into the locking tab and pry up. Replace spring tine and pry tab down. See figure 9. SCREWDRIVER FIGURE 9 PARTS 40" TINE DETHATCHER MODELS 486.243152, 486.24316 77191422202116161616121212121191171515151616161616161515151517861634411111018551313 REF. PART QTY. DESCRIPTION NO. NO. 1 23442 3 Hitch Arm Mount Bracket 2 23981 2 Hitch Bracket 3 43783 10 Spring Tine 4 47633 2 Spring Alignment Wire 5 43021 2 Wheel 6 24836 1 Tine Shield 7 23914 2 Hitch Mount Arm 8 24594 1 Lift Plate 9 24595 1 Axle Bracket 10 24596 1 Lift Handle 11 43029 2 Shoulder Bolt 12 23826 4 Angle Bracket REF. PART QTY. DESCRIPTION NO. NO. 13 HA21362 2 Nylock Nut, 3/8-16 14 43840 2 Hex Bolt, 5/16-18 x 1-1/4" 15 43063 15 Hex Bolt, 5/16-18 x 1" 16 47810 23 Nylock Nut, 5/16-18 17 44326 4 Carriage Bolt, 5/16-18 x 1" 18 43943 1 Handle Grip 19 44180 2 Hex Bolt, 5/16-18 x 2" 20 47623 1 Hitch Pin, 3/8" (Flat Head) 21 43343 1 Hair Cotter Pin, 1/8" 42107 1 Owner's Manual * Purchase Common Hardware Locally ® Registered Trademark / TM Trademark /SM Service Mark of Sears Brands, LLC ® Marca Registrada / TM Marca de Fabrica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commerce / MD Marque deposee de Sears Brands, LLC © Sears Brands, LLCGet it fixed, at your home or ours! Your HomeFor expert troubleshooting and home solutions advice: repair – in your home – of allmajor brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliancesand items like garage door openers and water heaters. 1-800-4-MY-HOME®(1-800-469-4663) Call anytime, day or night(U.S.A. and Canada) Our Home For repair of carry-in items like vacuums, lawn equipment, and electronics, call anytime for the location of your nearest Sears Parts & Repair Service Center1-800-488-1222(U.S.A.) 1-800-469-4663 (Canada) To purchase a protection agreement on a product serviced by Sears: 1-800-827-6655(U.S.A.) 1-800-36...
Questo manuale è adatto anche per i modelli :falciatrici - 486.24316 (781.42 kb)