valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
• Keep all parts of your body away from spinning blade/line and muffler. • Cut from your left to your right. CUtting on right side of shield will throw debris away from the operator. • Use only in daylight or good artificial light. • Use only for jobs explained in this manual. TRANSPORTING AND STORAGE • Stop the powerhead engine before carrying unit. • Keep muffler away from your body. • Allow engine to cool and secure unit before storing or transporting it in a vehicle. • Empty the fuel tank before storing or transporting the unit. Use up fuel left in the carburetor by starting the engine and letting it run until it stops. • Store unit and fuel in an area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. • Store unit so the blade or line limiter blade on shield cannot accidentally cause in ury. • Store un t ndoors, out of reach of children. SPECIALNOTICE:tovibra- Exposureor loss of feeling in the fingers, hands, or tionsthroughprolongedjoints, discontinue useofgasoline the use of this tool poweredtoolscauseblood and seek medical attention. An anti handcould vesselornerveinthefingers, damagevibration system does not guarantee the hands,andointsofpeoplepronetocir-avoidance of these problems. Users cuatondsordersorabnormaswerigs. who operate power tools on a continual Prolongeduseincoldweatherhasbeen and regular basis must monitor closelylinkedtoblooddamagetheir physical condition and the condition vesselinother wisehealthypeople.occur of this tool. Ifsymptomssuchas numbness, pain, loss of SAVE THESE INSTRUCTIONS strength, change in skin color or texture, CARTON CONTENTS Coupler Check carton contents against the following list. LOOSEN Model 358.792440 • Brushcutter Attachment • Handlebar (with Clamp and Knob) • Handlebar Clamp Base (with Spacer Tabs) • Shoulder Strap TIGHTEN Knob • Upper Shoulder Strap Clamp 2, • Lower Shoulder Strap Clamp (with Remove the tube cap from the Spacer Tabs) brushcutter attachment (if present). Handlebar Clamp Screws (4) 3. Position locking/release button of Shoulder Strap Clamp Screws (2) attachment into guide recess of Large nut for installing blade coupler. 4. Push the attachment into the cou- Cupped washer Trimmer head pler until the locking/release button 4-point weed blade (assembled on snaps into the primary hole. brushcutter attachment) 5. Before using the unit, tighten the • Wing nut (screwed onto shield) knob securely by turning clockwise. cutter attachment) Coupler Primary Hole • Metal shield (assembled on brush• Plastic shield \ /Guide Recess • Attachment Hanger • Hex Wrench • Container of line Examine parts for damage. Do not use Up!er L°ckin_g/[_ damaged parts. Tube Release Attachment NOTE: If you need assistance or find Button that parts are missing or damaged, call 1-800-235-5878. all}WARNING: Make sure the lock- ASSEMBLY ing/release button is locked in the pri=-& mary hole and the knob is securely all, WARNING: If received assembled, tightened before operating the unit. repeat all steps to ensure your unit is HANDLEBAR ASSEMBLY properly assembled and all fasteners are secure. DANGER: RISK OF CUT To • A hex wrench (provided) is required avoid serious injury, the barrier portion of the handlebar must be installed as for assembly. shown on the upper tube of the power- INSTALLING BRUSHCUTTER AT- head to provide a barrier between op- TACHMENT erator and the spinning blade. Attach CAUTION: When removing or instal-tube clamp above arrow on safety warn- ling attachments, place the unit on a ing decal on the upper tube (powerhead flat surface for stability. end of unit). Ensure handlebar is posi 1. Loosen the coupler by turning the tioned on handlebar clamp between the knob counterclockwise. arrows on the handlebar decal. 5 NOTE:Thetubeclampbasehasfour spacertabsattached.tabs Theseare providedtoadaptthisattachment for usewithpowerheadsa1"di thathave ameteruppertube(thetubeclampwill nottightendownonthe1"di securely ameteruppertubewithoutusingthese spacertabs).Thetabsmustbebroken offcompletelybeforeuseandplaced overthescrewholesontheclampbase. Thesetabsarenotneeded forpower headswitha7/8"uppertube. HANDLEBARBASE CLAMP Spacer Tabs Spacer_ Tabs o °ai i° e rer ae upper tube _I 1. Place the tube clamp over the upper tube above the arrow on the safety decal. 2. Position the clamp base under the upper tube and align the tube clamp and clamp base screw holes (use spacer tabs between tube clamp and clamp base if necessary to secure clamp, i.e. for 1" diameter upper tube). Handlebar POWERHEAD END Handlebar Clamp between arrows on handlebar decal Clam Knob Clamp Screws Arrow on Safety Decal ATTACHMENT END 3. Insert four screws into the screw holes. 4. Secure tube clamp by tightening screws with the hex wrench. 5. Position the handlebar as shown, ensuring the handlebar is positioned on the handlebar clamp between the two arrows on the handlebar decal. 6. Retighten handlebar byturning clamp knob clockwise until handlebar...