valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Bring the powerhead engine to cutting speed before entering the material to be cut. If the blade does not turn when you squeeze the throttle trigger of the powerhead, make sure the attachment is fully inserted into the coupler. Always release the throttle trigger and allow powerhead engine to return to idle speed when not cutting. The blade should not turn while the engine is running at idle. If the blade turns at idle, do not use your unit. Refer to the CARBURETOR ADJUSTMENT section of the powerhead manual or contact your Sears Service Center. • Maintain good firm footing while using the unit. Do this by planting feet firmly in a comfortable apart position. • Cut while swinging the upper part of your body from left to right. • As you move forward to the next area to cut, be sure to maintain your balance, and footing. RECOMMENDED CUTTING POSITION Cut using the 2 o'clock to 4 o'clock position of the 4 o'clock blade 2 o'clock WARNING: The operator or others must not try to clear away cut material with the engine running or the blade turning to avoid serious injury. Stop engine and blade before removing materials wrapped around blade or shaft. 13 MAINTENANCE SCHEDULE _WARNING: Always stop unit and disconnect spark plug wire before performing maintenance, CARE AND MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and decals Check or replace blade GENERALRECOMMENDATIONS The warranty on this attachment does not cover items that have been subjected to operator abuse or negli gence. To receive full value from the warranty, the operator must maintain the brushcutter attachment as instruct ed in this manual. CHECK FOR DAMAGED OR WORN PARTS Contact Sears Service Center for replacement of damaged or worn parts. • Blade Shield -Discontinue use of brushcutter attachment if shield is damaged. • CHECK FOR LOOSE FASTENERS AND PARTS • Blade nut • Fasteners INSPECT AND CLEAN UNIT AND DECALS • After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. WHEN TO PERFORM Before each use Before each use After each use Every 5 hours of operation • Wipe off unit with a clean dry cloth. BLADE MAINTENANCE _WARNING: The blade will contin ue to spin after the engine stops or af ter the throttle trigger has been raleased. To avoid serious injury, make sure the blade has stopped coasting and disconnect the spark plug before performing work on the blade. _WARNING: Always replace a blade that is bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged blade. Use only specified replacement blade. Wear protective gloves when handling or performing maintenance on the blade to help avoid injury. • Check blade for flatness periodically. Lay the blade on a flat surface to inspect for flatness. Throw away a blade that is not flat. LINE REPLACEMENT • Always use Craftsman replacement line. Choose the line size best suited for the job at hand. Red line is designed for cutting grass and small weeds. The black colored line is designed for cutting larger weeds and light brush. NOTE: Before inserting new line into the holes in the cutting head, identify the proper holes. Follow directions as shown on the line glide plate. 1. Remove the old line and line glide plate from the cutting head. 2. Clean entire surface of cutting head. 3. Reinstall line glide plate (see illustration). Align arrowwith: (_) when using medium (red) or large (black) line when using lines with diameter (_ smaller than medium (red)line (optional) Arrow Trimmerhead 14 NOTE:Lineglideplatemustberein-6. Correctly installed line will be the stalledheadinserting length both ends. incuttingbeforesame on newline. REPLACING THE CUTTING HEAD 4. Insertbothendsofyourline 1. Align hole in the dust cup with the throughtheproperholesinthe hole in the side of the gearbox bysideofthecuttinghead. rotating the dust cup. 2. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while removing and installing trimmer head. 5. Pull the line and make sure the line is against the hub and extended full through the positioning tunnels. Line againstthe hub Positionin Tunnel \ .A _ aWARNING: Perform the following steps after each use: • Allow attachment and gearbox to cool before storing or transporting. • Store attachment with blade shield in place. Position attachment so that any sharp object cannot accidentally cause injury. • Store the attachment in a dry, well ventilated area out of the reach of children. SEASONAL STORAGE Prepare attachment for storage at end of season or if it will not be used for 30 days or more. If your brushcutter attachment is to be stored for a period of time: Screwier _ 3. While holding the screwdriver in position, remove trimmer head by turning clockwise. 4. Thread replacement trimmer head onto the shaft by turning counterclockwise. Only tighten hand tight! 5. Remove the scr...