valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
1 YEAR LIMITED WARRANTY ON MODEL 291.376100 SEARS LAWN MOWER For one year from the date of purchase, when this Sears Lawn Mower is maintained and lubricated according to the instructions in the owner's manual, Sears will repair, free of charge, any defect in material aud workmanship. This warranty does not cover: Expendable items which become worn during normal use. Repairs necessary because of operator abuse or negligence, and the failure to maintain the equipment according to the instructions contained in the owner's manual. WARRANTY SERVICE IS AVAILABLE BY RETURNING THE SEARS LAWN MOWER TO THE NEAREST SERVICE CENTER/ DEPARTMENT IN THE UNITED STATES. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCKAND CO., D_lTWA Hoffman Estates, IL 60179 ITEMS IN CARTON One complete Hand Mower Chassis. Two upper handle sections. Two lower handle sections. One plastic bag including hardware for assembly of handle & handle grips. One 1/4" x 1 3/4" handle bolt- Two 1/4" x 2" handle bolts- Three 1/4-20 handle nuts Two retaining rings. Do not use Key Numbers when ordering Repair Parts, always use Part Numbers. Your mower is right hand (R.H.) or left hand (L.H.) as you push. CUSTOMER RESPONSIBILITIES Always use care when operating your Lawn mower. Keep clear of moving parts. Avoid striking or running into solid objects or debris in the area to be mowed. Keep the mower clean. Follow a regular maintenance and check schedule to provide efficient and safe operation. Well-cared for Lawn mowers will last longer and operate more efficiently. 2 16" HAND LAWN MOWERS MODEL NUMBER 291.376100 10 9 13 37 T T co KEY NO. PART NO. PART NAME 1. 30122 Ball Cup 2, 30137 Ball Bearing Assembly 3, 30004 Bearing Cone 4. 3030g Spring, Reel Adj. 5. 30308-0-10 Dust Cap 6. 30307 Reel Spacer 7. 30316 Raehet Pawl 8. 10122-2-10 Reel Assembly (hcludes Key Nos. 2 thru 6) 9. 30317-1 Axle Snap Ring 10. 30926 Hub Cap 11. 30337 Axle 12. 30733 Hex Nut 3/8" 13. 10426 Wheel & Tire 14. 30660 Hex Head Bolt 15. 30730 Cover Plate 16. 10326-17-10 Left Side Plate 16. A 10326-16-10 Right Side Plate 17. 30990 Retaining Rings 18. 10330-10 Torsion Bar Assy. REQ. 2 2 2 1 1 1 2 1 2 2 2 2 2 4 2 1 1 2 1 KEY NO, 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. PARTNO. 30737-3 30300 30737-2 31039 31043 30321 30119-5 10305-2-10 30519 30320 30071-4 30319-2 10018-3 31006 10443-9 30983-4 30991-1 30992 30991 30982-5 30747 11 910 13 23 PART NAME REQ. Left Pinion Gear 1 Adjusting Screws 4 Right Pinion Gear 1 Cutter Bar Bolt 2 2 Roller Bracket 2 Hex Nut Nylon Insert 2 Carriage Bolt 5/18" 1 Cutter Bar Stud 2 Roller Section 4 Roller Spacer 3 Roller Tube 1 Cutter Bar Assy. Complete Roller Assy. Roller Bracket Clamp 2 Complete Handle Asey. Lower Handle 2 Handle Bolt 1/4 x 2 2 Hex Nut Nylock 3 Handle Bolt 1/4 x 1 3/4 1 Upper Handle 2 2 Handle Grip MOWER BLADE ADJUSTMENT *The blades have been preadjusted before leaving the factory. *Misalignment can occur resulting in blades that are too loose or too tight. If this happens, you will notice a rough, uneven cut or a hard pushing mower. *All adjustments are made from the rear of the mower (opposite from the bar with the logo decal.) Each end of the cutting bar can be adjusted separately. *As you follow the instructions below, refer to Figure 1 for more information. *The cutting bar blade (located under the reel) pivots. The front screws move the cutter bar away from the blades, while the rear screws move the cutting bar toward the blades. *Adjusting the screws is a very sensitive procedure. 1/16th of a turn is considered a major adjustment. *Before tightening one adjusting screw, be sure to loosen the opposing screw an equal amount. LOOSENING THE BLADES *The cutter bar blade must be moved further from the cutting reel. *Loosen both back screws equally by turning them counter clockwise. *Tighten both front screws equally by turning them clockwise. TIGHTENING THE BLADES *The cutter bar must be moved closer to the cutting reel. *Loosen both front screws equally by turning them counter-clockwise. *Tighten both back screws equally by turning them clockwise. FIGURE 1 Adjusting Screws CHECKING ADJUSTMENTS *Turn mower upside down. *Insert a piece of paper (i.e., writing or newspaper) between the cutter bar and the reel blades, and carefully turn the reel blades by hand. *All blades should slice the paper evenly the entire length of the cutter bar while the reel turns smoothly. *If the mower has an uneven cut, an adjustment should be made to the appropriate side of the blades to attain an even cutting action. 4 , _AJRS OWNER'S MANUAL MODEL NO. 291.376100 To Call Toll Free For Service: 1-800-4-REPAIR (1-800-473-7247) For Parts: 1-800-FON-PART (1-800-336-7278) CRAFTSMRN,o 16" HAND LAWN MOWER The model number of your lawn mower is found on a decal on the cutter bar at the back of the mower. All repair parts are available for immediate purchase or spe...