valutazioni - , GPA: ( )

Istruzioni per l'uso Snapper, Modello 1694153

Produttore : Snapper
File Size : 621.49 kb
File Nome : 5dfffe51-2616-b314-a5bd-b370b8eb4917.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Note: The lid screen can be partially removed for easier cleaning and should be cleaned regularly. The blower housing and tube should be removed for cleaning. Inspect the grass bags for wear or damage. Make sure that there is a snug fit between mower deck, blower housing, tubes, and grass catcher cover. STORING THE GRASS CATCHER CAUTION Do not leave grass in bagger containers. Empty containers after each use and before storing. Failure to do so may result in spontaneous combustion which could develop into a fire. Clean the grass catcher thoroughly using a mild detergent (other products may damage the tube). Remove any debris from the the screen on the underside of the lid. If paint has been scratched on metal parts, touch up with paint, or apply a thin film of oil to prevent corrosion. Store in a dry area. Dry thoroughly before storing for a long period of time. Always store away from moisture. 3 Initial Assembly & Installation INSTALL MOUNTING PLATES BROADMOOR / 1600 / 2600 / LT SERIES Install Plates & Spacers 1. Mount the side brackets (B, Figure 1) to both sides of the frame using the holes shown. Secure with one 3/8-16 x 1 capscrew (C) and 3/8-16 nylock nut (A) per side. 2. Install the rear spacers (C, Figure 2). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/2-13 nylock nuts (A) per side. Figure 1. Install Side Brackets A. Nylock Nut, 3/8-16 C. 3/8-16 x 1 B. Side Bracket A B C A C D D B Figure 2. Install Rear Spacers A. Nylock Nuts, 1/2-13 C. Spacers B. 1/2-13 x 2-1/2 Capscrew D. 1/2” Washers INSTALL MOUNTING SPACERS CONQUEST / 1700 / 2700 / YT & PRESTIGE / 1800 / 2800 / GT SERIES NOTE: If installing this catcher on a unit equipped with a rear tiller, refer to the “Installation with a Tiller” section for special installation instructions. Install Spacers 1. Install the rear spacers (C, Figure 3). Secure with two 1/2-13 x 2-1/2 capscrews (E), washers (D), spacers (C), and 1/2-13 nylock nuts (A) per side. A C D D B Figure 3. Install Rear Spacers A. Nylock Nuts, 1/2-13 C. Spacers B. 1/2-13 x 2-1/2 Capscrew D. 1/2” Washers 4 Initial Assembly & Installation Figure 4. Upright Identification Use this upright with Broadmoor / 1600 / 2600 / LT Series Use this upright with Prestige / 1800 / 2800 / YT & Conquest / 1700 / 2700 / GT Series Figure 5. Assemble Catcher Frame A. Upright Support C. Horizontal Support B. 3/8-16 x 7/8 Capscrew D. 3/8-16 Whizlock Nut A B C D Prestige Mounting Holes Conquest & Broadmoor Mounting Holes A B D C A Figure 6. Assemble Catcher Frame (Prestige Shown) A. 3/8-16 Nut & Lockwasher C. 3/8-16 x 1 Capscrews B. Upright Support Assy. D. Lower Support A A DB B C C CATCHER ASSEMBLY - ALL MODELS Assemble Supports and Hitch 1. Refer to Figure 4 to select the proper upright support for your application. 2. Bolt the upright support (A, Figure 5) to the horizontal support (C). Secure with 3/8-16 x 7/8 capscrews (B) and 3/8-16 whizlock nuts (D). 3. Bolt the lower support plate (D, Figure 6) to the upright support (B) using two 3/8-16 x 1 capscrews (C), lockwashers, and 3/8-16 nuts (A). 4. Install the hitch side plates (B, Figure 7) and secure with four 3/8-16 x 1-1/4 capscrews (C), lockwashers, and 3/8-16 nuts (A). Figure 7. Assemble Catcher Frame (Prestige Shown) A. 3/8-16 Nuts & C. 3/8-16 x 1-1/4 Capscrews Lockwashers D. Support Assembly B. Side Plates 5 Initial Assembly & Installation Figure 8. Install Catcher (Prestige Shown) A. #10-32 Nut F. Bags B. Handle G. Hair Pin Clip C. #10-32 x 1/2 Screw H. Catcher Hitch D. Cover I. Spacers E. Hinge Pin I AB C D E F H G Install Cover and Bags 1. Mount the catcher hitch (H, Figure 8) on the frame spacers (I). 2. Hang the bags (F) on the horizontal support. 3. Install the handle (B) inside the cover. Secure with two #10-32 x 1/2” screws (C) and #10-32 nuts (A). 4. Rest the cover assembly (D) on the bags (F). 5. Install the two hinge pins (E) and secure with hair pin clips (G). 6. Open the cover and fasten cable (A, Figure 9) to support (B). The looped cable end fits over washer (C). A B C Figure 9. Install Cable A. Cable C. Washer B. Support F E A B C D Figure 10. Install Tubes A.Flange Nut D. Lower Tube B.Clip E. #10-32 Nut & Washer C.#10-32 x 1/2 F. Upper Tube Screw & Washer Assemble & Install Tubes NOTE: Install turbo blower at this time. 1. Locate the lower tube (D, Figure 10) and upper tube (F). 2. Assemble the upper and lower tubes using two #1032 x 1/2 screws (C), washers, and #10-32 nuts (E). 3. Insert the tube assembly into the catcher. 4. Connect the lower tube (D) to the turbo. Lock the clip (B) on the flange nut (A). 6 Normal Removal & Installation Figure 11. Normal Removal & Installation (Prestige Shown) A. Tubes B. Hair Pin Clip C. Frame Spacers D. Bags E. Clevis Pin F. Cover G. Clip E F D B C A G Normal Removal & Installation Figure 11. Normal Removal & Installation (Prestige Shown) A. Tubes B. Hair Pin Clip C. Frame Spacers D. Bags E. Clevis Pin F. Cover G. Clip E F D B C A G WARNING OPERATION WITHOUT TURBO ...