valutazioni - , GPA: ( )

Istruzioni per l'uso Bolens, Modello 111-516R000

Produttore : Bolens
File Size : 1.9 mb
File Nome : d0f3a752-6d9f-4ee6-9228-09b8b2e0b807.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

See figure 15. Metal Loop on Spark Plug Wire Rubber Boot FIGURE 15. I 2. Open fuel shut-off valve (if so equipped). Fiefer to separate engine manual. 3. Move throttle control lever all the way fotward. 4. Tecumseh engines only: Prime engine as instructed in the separate engine manual jacked with your unit. 5. Standing behind the unit, depress the blade control handle and hold it against the upper handle as shown. See figure 16. 6. Grasp the recoil starter handle and pull bacc rapidly, extending rope fully. Return it slowly to the rope guide. 7. After engine starts, move throttle control to < iesired engine speed. NOTE: If any problems are encountered, refer to the Trouble Shooting Guide on page 16. FIGURE 16. TO STOP ENGINE AND BLADE 1. Move throttle control lever to SLOW posi ion. 2. Release the blade control handle to stap the engine and blade. WARNING: The blade continues to rotate for a few seconds after the engine is shut off. 3. Disconnect the spark plug wire and ground it against the engine to prevent accidental starting while equipment is unattended. USING YOUR ROTARY MOWER A WARNING: Never operate your unit without either the rear deflector or entire grass catcher assembly in place. Be sure that lawn is clear of stones, sticks, wire, c r other objects which could damage lawn mower or«ngine. Such objects could be accidently thrown by the mower in any direction and cause serious personal injury to the operator and others. For the best results, do not cut wet grass because it tends to stick to the underside of the mower, preventing proper discharge of grass clippings, and could cause you to slip and fall. New grass, thick grass or wet grass may require a narrower cut. Blade speed should be adjusted to the condition of the lawn. For best results, cut off one-third or less of the total length of the grass. Lawn should be cut in the fall as long as there is growth. This mower is designed to be operated at full throttle to give you the best cut and do the most effective job of bagging the cut grass. A WARNING: If you strike a foreign object, stop the engine. Remove wire from spark plug, thoroughly inspect the mower for any damage, and repair the damage before restarting and operating the mower. Extensive vibration of the mower during operation is an indication of damage. The unit should be promptly inspected and repaired. ADJUSTMENTS A WARNING: Do not at any time make any adjustment to lawn mower without first stopping engine and disconnecting spark plug wire. CUTTING HEIGHT ADJUSTMENT An adjusting plate and thumb lever at each wheel position provides cutting height adjustment. Each adjusting plate has nine height positions. Height of cut will be changed when the thumb lever is moved from one hole to another. Simply depress the lever towards wheel and move wheel and lever assembly to desired position. All wheels must be placed in the same relative position. See figure 17. FIGURE 17. 10 THROTTLE CONTROL ADJUSTMENT If the throttle control requires adjustment or if it has been replaced, adjust as follows. 1. Remove the screw shown in figure 18. Remove the cable clamp from the cable. 2. Push the throttle control lever on the handle all the way forward to CHOKE position. Make certain the throttle control lever remains in this position. 3. Push the control lever on the engine as far toward the rear of the engine as it will go. Secure the cable in this position with the cable clamp and screw. Cable FIGURE 18. CARBURETOR ADJUSTMENTS A WARNING: If any adjustments are made to the engine while the engine is running (e.g. carburetor), keep clear of all moving parts. Be careful of heated surfaces and muffler. Minor carburetor adjustments may be required to compensate for differences in fuel, temperature, altitude and load. To adjust carburetor, refer to the separate engine manual packed with your mower. NOTE: A dirty air cleaner will cause an engine to run rough. Be certain air cleaner is clean and attached to the carburetor before adjusting carburetor. Refer to the separate engine manual. LUBRICATION A WARNING: Always stop engine and disconnect spark plug wire before cleaning, lubricating or doing any kind of work on lawn mower. Blade Control—Lubricate the pivot points on the blade control handle and the brake cable at least once a season with light oil. See figure 19. The blade control must operate freely in both directions. FIGURE 19. Discharge Chute Deflector—The torsion spring and pivot point should be lubricated periodically with light oil to prevent any rust or binding. Deflector must work freely. Wheels—Mower may be provided with ball bearing wheels. Lubricate at least once a season with light oil. Also, if the wheels are removed for any reason, lubricate the surface of the axle bolt and the inner surface of the wheel with light oil. A 4 oz. plastic bottle of light oil lubricant is available. Order part number 737-0170. Engine oil may also be used. Engine—Follow...