pieces of string) while the brush is rotating. 5. Move at reduced speed over uneven surfaces and on slopes to ensure you do not lose control or the machine does not tip over. Watch out for holes and other hidden dangers. 6. This collector is not intended to be driven on public roads. Watch out for traffic when using the machine close to streets and roads. 7. Ensure that all screws and nuts are tightened so that the collector is in good condition. 8. Stop and check the collector for damage following a collision. Any damage must be repaired before the collector is used again. 9. Follow all the instructions in this set of instructions regarding maintenance of the collector. DELIVERY The delivery comprises a box containing the components in fig. 2 as well as a bag. The bag contains the installation components in fig. 1. The following number (x) indicates the quantity of the relevant component. _ASSEMBLY_ Tools The following tools are required for assembly: • Adjustable wrench • Box wrenches 3/8 - 7/16 - 1/2 - 9/6 • Screwdriver • Pliers • Hammer Assembly of brush unit Figures and letters in brackets refer to the figures. 1. See fig. 3. Undo the existing nuts in the middle on the front of the brush unit (1). Remove the flat washers. Position the connecting rod (15) on the carriage bolts. Install the washers and the nuts. Do not tighten the nuts yet. 2. See fig. 3. Install the strut (9) on the brush unit with the aid of two screws (D) with the heads on the inside of the brush unit. Position two washers (I) and two locking nuts (G) on the outside. Do not tighten the nuts yet. 3. See fig. 3. The installation of the angle (14) determines the height of the hopper bag above the ground (see below). • The bottom of the hopper bag must be horizontal. • The distance to the ground must be 8-10 cm when the height setting arm (7) is in the central position. • Never allow the hopper bag to drag on the ground. • By installing the angle on the top or bottom of the connecting rod (15), along with the spacers, many different heights can be obtained. • Test which installation best suits the lawnmow-er in question. Continue assembly as follows: Install the angle ( 14) on the connecting rod with a screw (B) and a locking nut (F) in the front hole. Use a longer screw (A), the bracket (V) and a locking nut (F) in the rear hole. Position the strut (9) under the bracket (V). Do not tighten the nuts yet. 4. Tighten the nuts that were installed under point 3 above. Do not tighten too hard, as this could deform the tube. Press the connecting rod (15) down so that the strut (9) comes under the bracket (V), and press against the screw (A). Tighten all the screws and nuts that have been installed. 5. See fig. 4. Undo both locking nuts on the height setting tube (6). Remove the dished washers. Install the height setting lever (7) on the tube. Screw in the height setting lever. 6. Press the handle (S) onto the height setting lever with the finger grip facing forwards. 7. See fig. 4. Install the angle (W) on the connecting rod with a screw (C) and a locking nut (G). ENGLISH 8. Install the height setting strut (8) on the angle (W). Position the spacer (K) on the screw (E). Insert the screw with the spacer through the hole in the height setting strut and into the hole in the angle. Lock in place with the locking washer (J) and the nut (H). 9. Attach the other end of the height setting strut (8) to the height setting arm (7). Position the groove in the height setting strut opposite the square hole in the arm. 10.Screw into place with a carriage bolt (D), a flat washer (I) and the locking wheel (T). ll.See fig. 5. Install the two securing arms (5) on the outside of the brush unit. Screw the securing arms into the rear, lower holes with four screws (B) and four locking nuts (F). NOTE! The grooves in the securing arms must be facing up. 12.Install the hitch pin (U) and the two spacers (L) in the connecting rod. Lock with the locking pins (N). Assembling the hopper bag Figures and letters in brackets refer to the figures. 1. See fig. 6, 7. Insert the left-hand, upper hopper bag tube (1) in the hopper bag flap. Start at the cut-out in the middle of the hopper bag’s upper section. The holes in fig. 6 must be facing down. 2. Install the right-hand, upper hopper bag tube (1) in the same way and press the tubes together. 3. Secure the tubes by pressing in a plastic plug (R) through the holes. 4. See fig. 7. Locate the holes in the sides of the two upper hopper bag tubes. These will be used later. 5. See fig. 9. Assemble the two lower hopper bag tubes (3, 4). 6. See fig. 9. Secure the tubes by pressing in a plastic plug (R) through the holes. 7. Position the lower hopper bag tubes inside the hopper bag. 8. See fig. 10. Assemble the two upper and lower hopper bag tubes’ ends using the pins (Q) and the locking pins (M). 9. See fig. 11. Attach the hopper bag’s front strut to the lower hopper bag tubes using the pi...