valutazioni - , GPA: ( )

Istruzioni per l'uso Poulan, Modello 402337

Produttore : Poulan
File Size : 913.91 kb
File Nome : NOUS2005_402337.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

DRAWBAR A DRAWBAR B 3. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 4. Be sure support assembly is seated properly and secure with retainer spring supplied. DRAWBAR B (See Fig. 1D) 1. Discard adapters provided - not required for drawbar type B. 2. Align support assembly pin with hole in drawbar and hang assembly over the shoulder bolts. 3. Be sure support assembly is seated properly and secure with retainer spring supplied. 3064 SHOULDER BOLTS SUPPORT ASSEMBLY RETAINER SPRING PIN FIG. 1D FIG. 1B ADAPTER 6 CONTAINER ASSEMBLY (See Fig. 3) 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunless containerisprope rlyissubjecttowear anddetierioration.Checkbagfrequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 3 3 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 2 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 2) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor. 2. Lift and rotate cover to align cover brackets with support assembly tubes. 3. Slide cover assembly down onto the support tubes. FIG. 2 03024 COVER ASSEMBLY SUPPORT ASSEMBLY 7 LOWER CHUTE - MOWER WITH MOUNTING TAB (See Fig. 5A) 1. Raise and hold defl ector shield in upright position. 2. Place slot in lower chute over tab on mower and position lower chute over mower opening as shown. 3. Hook rear latch into fl ange hole on back of mower. 4. Hook front latch into tab hole on front of mower. • If your tractor is equipped with gauge wheels on the deck, then it will be necessary to hook the rear latch into the hole in the R.H. gauge wheel bracket. 5 CAUTION: Do not remove defl ector shield from mower. Raise and hold shield when attaching lower chute and allow it to rest on chute while in operation. WARNING Donotoperatemowerunless containeris properlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen cracked ordamaged.Useonlya recommendedreplacementcontainer. WARNING Donotoperatemowerunless containeris properlyisnstalled.Containeris subjecttowearanddetierioration.Checkbag frequently.Replacewhen cracked ordamaged.Useonlya recommendedreplacementcontainer. 03022 CONTAINER MOUNTING (See Fig. 4) 1. Install one container to left side fi rst with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right con tain er should always over lap left con tain er at center supports. 2. Close cover and lock latch handles over center support tubes. 4 FIG. 4 COVER LATCH HANDLES CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING CENTER SUPPORT TUBES 03058 DEFLECTOR SHIELD HINGE BRACKET REAR LATCH REAR GAUGE WHEEL BRACKET DEFLECTOR SHIELD FRONT LATCH WITHOUT REAR LATCH GAUGE WHEELS WITH REAR GAUGE WHEELS EXTENDED EDGE "B" Must be under defl ector shield and along side the hinge bracket FIG. 5A TAB LOWER CHUTE - MOWER WITHOUT MOUNTING TAB (See Fig. 5B) 1. Lower mower deck to its lowest cutting position. NOTE: If equipped, remove mulch cover from mower deck and store in a safe place. 2. With your right hand, raise and hold deflector shield in upright position. 3. With your left hand, hold lower chute as shown and position lower rear edge of chute between gauge wheel bracket tab and mower housing, then carefully release deflector shield and hook rear latch to mower deck. 4. Raise deflector shield and align "B" on lower chute extended edge with "B" on mower housing. 5. With your right hand, push firmly on the lower chute until the extended edge slides under the deflector shield and along side the hinge bracket as shown. 6. With chute in proper position, hold the chute securely, so it does not move, while hooking the front latch to the mower deck. NOTE: While hooking the latches, the deflector shield may try to push the chute away from the mower deck opening. It is important to hold the chute in position while hooking the latches to the mower deck. • If your tractor is equipped with gauge wheels on the deck, then it will be necessary to hook the rear latch into the hole in the R.H. gauge wheel bracket. BB BB 02558 ALIGN CHUTE "B" WITH MOWER "B" OPTIONAL GAUGE WHEEL AND BRACKET PUSH IN PLACE LOWER REAR EDGE BETWEEN GAUGE WHEEL BRACKET TAB AND MOWER ...