valutazioni - , GPA: ( )

Istruzioni per l'uso Poulan, Modello 140603

Produttore : Poulan
File Size : 657.96 kb
File Nome : NOUS2003_140603.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Look carefully at the mower deck on your tractor and compare the deck mandrel to the illustrations below. If your mower deck mandrel looks like STYLE "A", your tractor is ready - proceed with the grass catcher assembly. If your mower deck mandrel looks like STYLE "B", go to the PREPARATION section in this manual. DECK MANDREL STYLE "B" DECK MANDREL STYLE "A" UPPER CHUTE GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING WING NUT W A R N I N G D o n o t o p e r a t e m o w e r u n l e s s c o n t a i n e r i s p r o p e r l y i s n s t a l l e d . C o n t a i n e r i s s u b j e c t t o w e a r a n d d e t i e r i o r a t i o n . C h e c k b a g f r e q u e n t l y . R e p l a c e w h e n c r a c k e d o r d a m a g e d . U s e o n l y a r e c o m m e n d e d r e p l a c e m e n t c o n t a i n e r . W A R No 02I Nr Ge m o w e r u U D o n o t p e a t n l t i o n .e s s c o n t a i n e r i s p r o p e r l y l i s n s t a l l e d . Ca c o ne t a i n e r i s s u b j e c t t o w e a r a n d d e t i e r i o r a C h e c k b a g f r e q u e n t y . R e p l c r a c k e d o r d a m a g e d . l l w h e n s e o n y a r e c o m m e n d e d r e p a c e m e n t c o n t a i n e r . 341 PARTS IDENTIFICATION COVER DUMP BAG INDICATOR CHUTE LATCH LOWER CHUTE NOTE: When right hand (R.H.) and left hand (L.H.) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. (1) 3/8" Wrench (1) Drive Ratchet THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER: (1) 1/2" Wrench (2) 9/16" Wrenches (1) 3" or longer Extension (1) Short Handle(1) 1/2" Socket Phillips Screwdriver (1) 9/16" Deep well Socket CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 MOWER DECK BAFFLE (See Fig. 1) Use Hardware - - GROUP "A" 1. Raise your tractor mower deck to its highest position. 2. Install the hex bolt, and locknut through mower deck baffl e and tighten securely. 02342 HEX BOLT MOWER DECK BAFFLE FIG. 1 LOCKNUT 2 2 REAR MOUNTING BRACKET (See Figs. 2A, 2B & 2C) NOTE: If your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the mounting bracket, lanced tabs towards bottom, on the bolts. Discard hardware group "B" and disregard the remaining Step 2 instructions. LANCED TABS 02337 TOWARD BOTTOM SHOULDER BOLTS FIG. 2A If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. Use Hardware - - GROUP "B" Only one set of hardware in GROUP "B" will be used to mount the rear mounting bracket. To determine which set is correct for your tractor, check to see if there are (2) two upper corner ribs on each side of drawbar. If your tractor has the upper corner ribs, use the (4) four self tapping shoulder bolts. If your tractor does not have the corner ribs, use the set of (4) four bolts and locknuts. SELF TAPPING SHOULDER BOLTS (See Fig. 2B) 1. Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. 2. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. 02336 UPPER CORNER RIBS LANCED TABS TOWARD BOTTOM FIG. 2B UPPER CORNER RIBS SELF TAPPING SHOULDER BOLTS BOLTS AND LOCKNUTS (See Fig. 2C) IMPORTANT: ON TRACTORS WITH FUEL TANK UNDER THE SEAT,THE DRAWBAR MUST BE REMOVED FOR INSTALLATION OF MOUNTING BRACKET.TO REMOVE DRAWBAR, REMOVE TWO HEX BOLTS ON BOTH SIDES OF DRAWBAR. 1. Assemble the mounting bracket, lanced tabs towards bottom, using the four smaller inside holes on the drawbar. NOTE: If your tractor drawbar does not have the four correct holes for mounting the bracket, refer to the PREPA RATION sec tion of this manu al. 2. Install the four bolts and locknuts as shown and tighten securely. 3. If drawbar was removed from tractor, reassemble to tractor at this time. Tighten securely. BOLTS 02335 DRAWBAR MOUNTING BOLTS (BOTH SIDES) LANCED TABS TOWARD BOTTOM LOCKNUTS FIG. 2C 3 3 COVER SEAL (See Fig. 3) No hardware required 1. Align mark on seal with mark at cover opening. 2. Work seal into opening so cover sits between flanges of seal. ALIGNMENT MARKS 02085 COVER SEAL FIG. 3 7 SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "C" CAUTION: Container sup port is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 1. Rotate cover assembly onto its side as shown. 2. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. 02091 LOCKNUTS CARRIAGE BOLTS SUPPORT POST FIG. 4 5 5 MOUNTING TO TRACTOR (See Fig. 5) Use Hardware - - GROUP "D" NOTE: For ease of assemb...