valutazioni - , GPA: ( )

Istruzioni per l'uso Poulan, Modello 183159

Produttore : Poulan
File Size : 604.53 kb
File Nome : NOUS2003_183159.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: • Depress clutch/brake pedal fully and set parking brake. • Place gearshift/motion control lever in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key "OFF" and remove key. • Make sure the blade and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. ASSEMBLY MOWER DECK BAFFLE (See Fig. 1) Use Hardware - - GROUP "A" 1. Raise your tractor mower deck to its highest position. 2. Install the hex bolt, and locknut through mower deck baffl e and tighten securely. LOCKNUT 5 02342 HEX BOLT MOWER DECK BAFFLE Fig. 1 6 02644 02645 02643 BAGGER SUPPORT ASSEMBLY (See Figs. 2A & 2B) NOTE: If your tractor already has four (4) shoulder bolts installed on the rear drawbar, simply hang the support assembly on the bolts. Discard the four (4) shoulder bolts supplied and go on to Step 3 in struc tions. 2 SELF TAPPING SHOULDER BOLTS FIG. 2C PULL OUT ON STOP BRACKET TO REMOVE SUPPORT ASSEMBLY FIG. 2B If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. Use Hardware - - GROUP "B" 1. Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. 2. Hang the support assembly on the bolts. SHOULDER BOLTS FIG. 2A TO REMOVE THE SUPPORT ASSEMBLY (See Fig. 2C) 1. Pull outward on the stop bracket enough to allow support assembly to be lifted up and away from drawbar. 3 FIG. 3 MOUNTING COVER ASSEMBLY TO SUPPORT ASSEMBLY (See Fig. 3) NOTE: For ease of assembly, you may wish to obtain the as sis tance of another person for mounting cover assembly to tractor. 1. Position cover assembly on ground behind tractor as shown. 2. Lift and rotate cover to align cover bracket with support assembly. 3. Slide cover assembly down onto the support assembly. 02646 COVER ASSEMBLY SUPPORT ASSEMBLY SUPPORT ASSEMBLY SUPPORT ASSEMBLY 7 4 02343 FIG. 6 CAUTION: Do not remove discharge guard from mower. Raise and hold guard when attaching lower chute and allow it to rest on chute while in operation. LOWER CHUTE (See Fig. 6) Use Hardware - - GROUP "C" 1. Raise and hold defl ector shield in upright position. 2. Slide back edge of chute over rear corner of mower deck and pivot forward. 3. Align slot in lower chute with hex bolt in mower deck baffl e and close chute over deck openning. 4. Secure with washer and wing nut. 6 WARNING Donotoperatemowerunlesscontainerisproperlyis subject towearanddetierioration.Checkbagfrequently. Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING 02082 CONTAINER MOUNTING (See Fig. 5) No hardware required 1. Install one container to left side fi rst with warning to outside of unit. Install other container to right side. NOTE: Right con tain er should always over lap left con tain er at center sup port. 2. Close cover and lock latch handle over center support tube. 5 CENTER SUPPORT TUBE COVER LATCH HANDLE CONTAINER WARNING CONTAINER HANDLE CONTAINER WARNING FIG. 5 DEFLECTOR SHIELD MOWER DECK BAFFLE WASHER WING NUT HEX BOLT CONTAINER ASSEMBLY (See Fig. 4) No hardware required 1. Place bottom half inside of top half, as shown. 2. Place one foot inside bottom half and lift top half to meet bottom half. 3. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. 4. Repeat for other containers. PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF 02089 CONTAINER BOTTOM HALF CONTAINER TOP HALF ASSEMBLY CHECK: Squeeze sides of lower half of contain er and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. LOCKING TAB WARNING Donotoperatemowerunlesscontainerisprope rlyissubjecttowearanddetierioration.Checkbag frequ ently.Replacewhencrackedordamaged.Useonlyarecomme ndedreplacementcontainer. 02097 FIG. 4 02739 CONTAINER BOTTOM HALF CONTAINER TOP HALF 8 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjectto wearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. 02345 WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacementcontainer. WARNING Donotoperatemowerunlesscontainerisproperlyisnstalled.Containeris subjecttowearanddetierioration.Checkbagfrequently.Replacewhen crackedordamaged.Useonlyarecommendedreplacement container. 02344 UPPER CHUTE (See Figs. 7A & 7B) No hardware required 1. Lower mower deck to its lowest cutting p...