Beatrice, NE. Printed in U.S.A. CONTENTS SAfETy..................................................................... 5 GENERAL OPERATION................................ 5 SLOPE OPERATION.....................................5 CHILDREN ................................................... 6 SERVICE....................................................... 6 CONTAINER CONTENTS ......................................... 8 ASSEmBLy ............................................................... 9 OPERATION

1. Place hitch on the rear of the mower. Rear Engine Guard Engine Guard Bolts Engine Guard Bolts 3. Install two of the previously removed bolts through rear of the hitch weldment. 4. Secure the sides of the hitch to the frame with 5/16-18 x . bolts and washers from the new hardware, (two per each side). Previously Removed Hardware Hitch Mount Tube 8063-044 8063-045 8063-046 BAGGER SUPPORT -2008 and Prior Models 10 ASSEMBLY 1. Position upper chute support against bagger inlet, flush at outer edge

3 Edger-Trimmer Features ...................... 4 Assembly............................................... 5 Attaching the Handle.............................. 5 Installing Throttle Wire............................ 5 Fill Engine With Oil................................. 5 Operating Your Edger- Trimmer ..................................................6 Correct Engine Operation....................... 6 Fuel Specication ................................... 5 Oil Specication..........................

Model LE389 Read and keep this book for future reference. This book contains important information on SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE. PRODUCT INFORMATION The owner must be certain that all the product information is included with the unit. This information includes the INSTRUCTION BOOKS, the REPLACEMENT PARTS and the WARRANTIES. This information must be included to make sure state laws and other laws are followed. 4.2006 MS-3616MA Congratulations... Thank you for purchasing this qu

These settings are approximate and may vary due to physical characteristics of the product. Walking speed. wear, condition of the turf and humidity, may cause actual rate setting to deviate. No expressed nor implied warranty or guarantee is provided as to coverage or uniformity indicated by these rate settings. 70 LP Setting 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 PrizelawnPrizelawnPrizelawnPrizelawnBF-1 /SS,HVO, CBRlll, Setting G H J K M N N1/2 O P1/2 Q R S T U V X Z Lesco Hi-WHEEL Setting E

Remove components from carton and place spreader upside down on a padded surface. Install LH. & RH. handle braces to frame as shown using four (4) 1/4-20 x 2 1/4” hex bolts and nuts but do not tighten. ASSEMBLYASSEMBLYASSEMBLYASSEMBLY3. Turn spreader upright. For ease of assembly, make sure ON/OFF cable is on top of handle braces. With DOT on the handle assembly facing as shown, secure clamp bracket using a #10 x 3/4 slotted sheet metal screw. Install end of handle assembly between handle braces

NOTE: Handle carefully so as not to damage full bag in dicator. 3. Push in and turn upper chute until it is in line with lower chute. 4. Align the bosses on lower chute with alignment slots on upper chute and slide together. 5. Secure with rubber latch by hooking hole in latch over latch pin. LEVEL MOWER DECK Be sure deck is properly leveled for best mower per for - mance. See your tractors owner's manual for instructions. 6 COVER UPPER CHUTE FIG. 5A HANDLE FULL BAG INDICATOR LOWER CHUTE BOSSES

539 111139....1 .... COVER ASSM, COMPLETE 11.. 532 179746....1 .... BAGGER, FRAME INCLUDES ITEMS 2-4 12.. 532 192786....1 .... PIN, HINGE 2.. 532 127533....1 .... SCREEN, COVER 13.. 532 400226....2 .... CONTAINER, SOFT BAG 3.. 532 155042....1 .... STRIP, REINFORCEMENT 14.. 539 105408....8 .... WASHER #10 FLAT 4.. 532 130895....1 .... LATCH HANDLE, COVER 15.. 539 976977....4 .... NUT #10-24 HEX NYLOC 5.. 539 976952....9 .... SCREW #10-24 x 5/8 16.. 539 106312....4 .... HMS #10-24 x . 6.. 532 1327